RobbieG1983

Error code decriptions:

Error Code: 18440 P2008

  This error code is " Generic OBD " ( for each automaker same description and meaning).

  The following symptoms / causes / solutions are specific to VAG cars ; to other car manufacturers who may differ in detail.

nl Valve Intake Manifold 1 Airflow Control for electrical fault in circuit

du Saugrohrklappe 1 für Luftstromsteuerung elektrischer Fehler im Kreis Strom

and Intake Manifold Flap, Bank 1 Circuit / Open - MIL On

 

Additional information on the error codes

Possible symptoms :

 

    ERROR lamp (MIL) lights

 

Possible causes:

 

    Fuse (s ) are poorly connected or defective

    B + terminal 30 and B + terminal 15 is defective

    Valve is contaminated

    Valve is stuck
    Wiring and / or connections to / from the control valve defect

    Valve control does not work (properly)

 

Possible solutions:
 

    Check / replace fuse (s)

        remove the fuse (s) out

        Make the ends of the fuse (s) clean (very light sanding with fine sandpaper , then very little contact spray on it)

        fuse (s ) by measuring with a multimeter ( the fuse (s ) sometimes looks fine , but appearances can be deceiving )

        fuse (s) replace / replace

    Check B + B + terminal 30 and terminal 15

    Check postition valve ( measuring blocks ) / Replace Valve

    Disassemble the valve and clean him

 

Extra info :
    These are the valves in the intake manifold. These sit there for part load, a tdi has through this way stratified

    combustion = more economical. link , link . So to see something with the adjustment.

    Flashy nothing serious as long as they are open , it does not cost . And in consumption also is not so bad .   

    This gives no lights etc in the dashboard. If you have full power , you can just drive

--------------------------------------------------

Layout Code : P15A1

  This error code is " Manufacturer Specific " ( for each automaker a different description and meaning). The following

  description / symptoms / causes / solutions are specific to VAG cars.

nl Sensor Neutral Position unlikely signal

du and Neutral position (NP ) sensor implausible signal

Additional information on the error codes

Possible symptoms :

    ERROR lamp (MIL) lights

 

Possible causes:

 

    Wiring and / or connections faulty

    sensor defective

Possible solutions:

 

    Check / repair wiring and connections

    Check ( measuring blocks ) / replace Sensor

----------------------------------------------------

Error Code: 18441 P2009

  This error code is " Generic OBD " ( for each automaker same description and meaning). The following symptoms / causes /

  solutions are specific to VAG cars ; to other car manufacturers who may differ in detail.

nl Valve Intake Manifold 1 for Airflow Control signal is too weak

du Saugrohrklappe 1 für Luftstromsteuerung Signal zu klein

and Intake Manifold Flap ; Bank 1 Short to Ground - MIL ON
 

Additional information on the error codes

Possible symptoms :

    ERROR lamp (MIL) lights

Possible causes:

    Fuse (s ) are poorly connected or defective

    B + terminal 30 and B + terminal 15 is defective

    Valve is contaminated

    Valve is stuck

    Wiring and / or connections to / from the control valve defect

    Valve control does not work (properly)

 

Possible solutions:

    Check / replace fuse (s)

        remove the fuse (s) out

        Make the ends of the fuse (s) clean (very light sanding with fine sandpaper , then very little contact spray on it)

        fuse (s ) by measuring with a multimeter ( the fuse (s ) sometimes looks fine , but appearances can be deceiving )        fuse (s) replace / replace

    Check B + B + terminal 30 and terminal 15

    Check postition valve ( measuring blocks ) / Replace Valve   

    Disassemble the valve and clean him
 

Extra info :

    These are the valves in the intake manifold. These sit there for part load, a tdi has through this way stratified

    combustion = more economical. link , link . So to see something with the adjustment. Flashy nothing serious as long

    as they are open , it does not cost . And in consumption also is not so bad . This gives no lights etc in the dashboard.

    If you have full power , you can just drive

    Read this post on the audiforum.nl

-----------------------------------------------------------

Error Code: 17424 P1016

  This error code is " Manufacturer Specific " ( for each automaker a different description and meaning). The following

  description / symptoms / causes / solutions are specific to VAG cars.

nl valve for filter bypass valve ( N275 ) interruption

du Ventil für Bypass Klappe Luftfilter ( N275 ) Unterbrechung

and Bypass Flap filter valve ( N275 ) Open Circuit

Additional information on the error codes

Possible symptoms :

    unknown

Possible causes:

    Wiring and / or connections faulty

    ( N275 ) faulty

Possible solutions:

    Check the wiring and all connections

    Check ( measuring blocks ) / replace ( N275 )

------------------------------------------------------------
 

Error Code: 16484 P0100 (the corresponding 'old VAG code' is: 00553)

   This error code is "Generic OBD" (for each
   automaker same description and meaning). The following symptoms / causes  / solutions

   are specific to VAG cars; to other car manufacturers who may differ in detail.

nl Air Flow Sensor (G70) supply

du Saugrohrdruck (G70) Anschlußspannung

and Mass Air Flow (MAF) (G70) Supply Voltage

Additional information on the error codes

 

Possible symptoms:

 

     Probably no real serious problems

     reduced ability

     Infrequent / rough running

     Engine stalls

     Fuel consumption too high

     exhaust smokes

     ERROR lamp (MIL) lights

 

Possible causes:

 

     This error code is usually caused when you plug the LMM disconnecting and then turn it on contact. The ECU sees no LMM more

     Fuse (s) are poorly connected or defective

     Check whether the MAS is not too close to a) ignition / bobinedraden solenoid valve, c) relays, d) motor    

     Bad contacts to / from the LMM (check especially the connection to the ECU)
     Check for leaks past the LMM

     The air filter is clogged (leak in the air intake)

     Exhaust is blocked

     Correct values ​​for the LMM are ao calculated on the basis of the values ​​that pass the MAP sensor. So check the MAPsensor:

     MAP sensor itself

     Wiring and / or connections faulty

     Leakage to / from the MAP sensor

     The LMM is polluted

     if you use a reusable air filter that is soaked in oil, beware that there is not too much oil is (Just standard)

     The LMM (G70) is broken

Possible solutions:

     Error codes in the LMM are sometimes difficult to solve / able to put you on the wrong track

     Reset the error code, and hope he does not come back

     Before replacing the LMM (G70), first try the following once, maybe it helps:

     Replace the air filter

     make the MAS clean (blow or special cleaner), it does not often, but you never know

     reset error codes

     Check / replace fuse (s) remove the fuse (s) Make the ends of the fuse (s) clean (very light sanding with fine sandpaper, then very little contact spray on it)

     fuse (s) by measuring with a multimeter (the fuse (s) sometimes looks fine, but appearances can be deceiving

     fuse (s) replace / replace

     Check the exhaust for blockage

     Check / repair wiring and connections to / from the LMM
     Check for leaks around the LMM

     Check the voltage of the LMM

     Check (measuring blocks) / replace LMM
     Check (measuring blocks) / replace the MAP sensor

     The dealer if there is a software update for the error check

     The ECU, replace but that is the last solution

 

Extra info:

     LMM (G70)

     Air pressure sensor in the intake manifold / MAP sensor (G71)

     For model years 1995-2004 (?), The TDI VAG a
     bad reputation for the MAS. Which is slowly dirty and dirty (not easy to clean), and loses slowly (!)

     Functionality, somewhat irregular course and loss of ability as a result. The functionality can be tested

     by using [01 engine] a log, [meas.blocks-08], group 003 (3rd gear, floored by 1700-4000rpm)].