David021

Hello! I have a problem with my 2013–2016 Audi A4 B8.5 2.0 TDI 177 hp Quattro 6-speed manual. I’m getting the "Steering Lock: Contact Workshop" error on the dashboard. In VCDS, the error appears in 05 - Acc/Start Auth. as 03026 - Enabling Terminal 15 with faults 006 and 009 (Short to Ground / Short to Plus). The ignition turns on, but after pressing the clutch and pushing the key again, the car doesn’t even attempt to crank. Instead, it turns the ignition off. If I hold the clutch pedal down with the key in the ignition slot, it eventually starts after multiple attempts—sometimes on the second try, sometimes on the 20th. This error and starting issue are intermittent. If I clear the error or disconnect the battery, it works for 1–2 days (or less). The battery is fine; it was replaced last year and coded to the car. The steering lock also functions correctly—the wheel has never locked or failed to unlock. This issue occurred last year. The mechanic opened the plenum chamber under the windscreen, cleaned the cables in the junction box (center of the plenum) with sandpaper, and sprayed them with contact cleaner. I repeated this process this year, but it didn’t help, and the cables showed no visible oxidation. Worth noting: I’ve had drainage problems in the plenum chamber. Water pooled there because the drains were blocked. The issue happened last year during heavy rain and has recurred this year under similar conditions. Here is the VCDS scan for the 05 - Acc/Start Auth. (BCM2) module: (If needed I can provide a full scan for the car) Address 05: Acc/Start Auth. (J393) Labels:. 8K0-907-064-05.clb Part No SW: 8K0 907 064 FD HW: 8K0 907 064 FD Component: BCM2 2.0 H10 0602 Revision: 00002001 Coding: 03A20000000000000000 Shop #: WSC 06335 000 00000 VCID: 77ABEBC16FCEBA623E1-8022 Subsystem 1 - Part No SW: 8T0 959 754 D HW: 8T0 959 754 D Component: FBSAUDIB8 IDG H60 0072 Serial number: 0812000010933010 Subsystem 2 - Part No SW: 8K0 905 852 E HW: 8K0 905 852 E Component: J764 ELV MLB H40 0046 Serial number: 2312000005203016 2 Faults Found 03026 - Enabling Terminal 15: 009 - Open or Short to Ground Freeze Frame: Fault Status: 00101001 Fault Priority: 2 Fault Frequency: 1 Reset counter: 97 Mileage: 353326 km Time Indication: 0 Date: 2025.06.11 Time: 16:20:33 03026 - Enabling Terminal 15: 006 - Short to Plus - MIL ON Freeze Frame: ~ Raw, Index/Key Err.: 229 226 127 (no units): 1.4673 Raw, Index/Key Err.: 187 055 193

Hello! I have a manual 6 speed Audi A4 B8 2.0 TDI Quattro from 2012, its the facelifted version. I have enabled with VCDS the drive-select function on the MMI (MMI 3G) , but only Comfort and Individual modes are selectable. I have watched a video about this, it seems like the guy in the video enables an adaptation in 09 with a security key, which is 20113 , my VCDS software also tells me that the security key to unlock adaptation features in that module is 20113 , but if I type it in and press the "Do it!" button it gives me an error code , "Security key not authorised! , Error: Unknown (00) (0x00)" or something like this , and I can't enable multiple modes. (I know that it won't do anything I just want the interface of the driveselect in my car to look like and feel like an audi that has it.) Thank you in advance for the help! Kind regards, David.

Hello. Took the car to a mechanic today, sadly it's the turbo that's doing this noise and the problem with the acceleration.

Hey. Thank you for the help. I'm taking the car to a mechanic today as the noise became more loud and it's coming from the turbo sadly, or somewhere near the turbo.

Thanks. Is there any way to check these two?

No fault codes. When I start the engine there is a squealing noise when accelerating. It disappears after changing to third gear. Does not appear again until I start the engine again or if I'm going down a hill for 5-10 minutes without pressing the accelerator , then it appears again except it's much louder but disappears after some time.

Hello. I have an Audi A4 B8 2012 Facelift 2.0 Diesel. The car stutters when accelerating, it started only at 3.000 + RPM-s, now it stutters even at low 2.000. The "motorsteuerung" light (EPC Light) started flashing suddenly after an acceleration in third gear. After stoping and restarting the car the flashing EPC light stoped, but the car still drives like !Removed! when accelerating. Can it be the throttle body or more likely the throttle position sensor?

Turns out it was a faulty throttle body. I took it out and cleaned it, seems like the problem temporarily disappeared. 🙂

Update: It still does it sometimes , not always and not that often as before, but now it can happen even at lower RPM-s. 2000 or 2500 , mostly in second and third gear. I still can't figure it out what could it be.

I don't think so, the car accelerates normally as it should , it has all it's power. It doesn't seem like any power is missing.

As I mentioned, the injectors were changed with brand new ones maybe 3.000 kms ago so I do not think that they are contaminated. I have a rubber clamping at the muffler which is worned out, so the muffler moves a bit, sometimes I can hear it clanking , I will need to change that, but I don't think it should not cause an issue like this. But good news, as I was driving it a little bit harder maybe a week ago, accelerating all the way through first , second, third and fourth, I did this maybe three times and the problem dissappeared. So maybe something was clogged up or was not functioning as it should. It seems like a little bit of hard driving solved this issue.

Hello. My Audi has a "hickup" where the engine cuts out for a split second , it does it only one or twice at around 3.000 RPM, at 4.000 or above it's more frequent and it doesn't happen all the time. Not lights on the dash, nothing shows up on VCDS scan , the oxygen sensor was changed recently as well as the injectors with new o-rings. Any ideas what could it be?

Yes. You have to change or refurbish the injectors. Had the same problem. I recommend that you change or refurbish all of the injectors, so you won't have any problems afterwards.

I do not hear any weird noises. Can you describe the noise you are hearing?

Fault code from VCDS software: Access/Start Auth - Enabling Terminal 15 - 03026 Any ideas what this code means? Have anyone had this problem?