All Activity
- Past hour
-
daveyboy1967 started following Engine Management light on
-
He says it's the 1.8 turbo petrol in the OP.
-
Petrol or diesel David?
-
So are you fitting a new track rod end, and if so what brand is it and where did you buy it from?
- Today
-
Upon reflection is it possible the fuel pump is giving up, as per the hard turnovers before starting, not so perfect idling, lean reading and not so good mpg ? My mechanic has a sophisticated code reader and every check he did came back with no fault apart from the lean reading
-
i like boats joined the community
-
Billy nel started following Radio code and blank mmi
-
Hi can anyone help me with my radio code .I have recently bought the car and the battery went dead. as its old so when I put the new one on the radio is in safe mode. The code in the book didn'twork and its on 1 now so not goingto get it locked out.Also the mmi screen is blank.is the a rest procedure for that. Any help much appreciated
-
Billy nel joined the community
-
Keep us posted on how you get on 🙂
-
Glad you got sorted 🙂
-
Yes it has a Hex at the end of the thread. It’s almost like it runs out of thread before you can torque it up.
-
Does the end of the thread have a hex/ torx or triple square like the lower balljoint?
-
Beach56 started following 2013 A8 lwb executive 4.0 TFSi
-
Hi, Selling my 2013 A8 Black 4.0 TFSi, 91,000 miles. In great condition, MOT till October 2025. If any interest i have plenty of pictures. £11250 Im in TA6
-
That’s the problem, even with a jack on the verge of lifting it into the air it’s still spinning and not locking on.
-
Rybrook started following Outer tie rod end problem!
-
The balljoint should have a taper, when it's done up it should pull it's self tight and lock. You can use a jack on the bottom of the track rod to add extra pressure to help tighten it and stop it spinning.
-
s.yvo joined the community
-
Yes i am.
-
G.P joined the community
-
Right guys....... i put a 7.5 am fuse in No 1 in box under bonnet ( the box I messed about with Expensive lesson, although when the auto electrician check the cluster before I sent it off he said it was dead....... Thanks to everyone for their input and help... I am sure I will be back onwith more questions soon...
-
Chris James started following Audi S7 Pic 17th May'24 (11).jpg , Audi S7 Pic's 17th May'24 (4).jpg , Audi S7 Pic 17th May'24 (7).jpg and 1 other
-
-
-
Cheers OJ! I guessed as much and fortunately have a laptop running an older version of windows. -the one before 10 I think - and now that I think about it, my bruv (who has the full VCDS setup) has loaded parts of the workshop manual as relates to bodywork on it I think......but he lives 300+ miles away near Newcastle and is currently on the other side of the planet for work.....I guess if it can hold the manual, it could take the software....I have heard it's pricey to obtain but that might just be scuttlebutt, I dunno. Ho hum, onwards and (hopefully) upwards. Thanks again.
-
-
-
Hi SM, sounds like your garage is the way to go but to scare your question, one end of the cable is plugged into the car inside the cabin on right of driver’s footwell, other bit usually goes into a laptop running Windows. Good luck with your next stages.
-
Nor the 2nd for me Jake.
-
Hello Leo, Are you talking track rod end here?
-
Hello Tom, Returning the car to the seller 5 months on??? 90 days is a typical warranty period. Your issues maybe (just maybe) associated with your statement ‘…done barely any miles on it…’. On the basis of eliminating simple low cost investigations, it would be well worth getting the battery efficiency checked - Halfords stores will do that. Spurious messages are often associated with below par battery efficiency, and your situation will be aggravated by periods of lack of use. Take the car for an approx. 30 mile run before getting Halfords to report on the battery’s efficiency. Please let us know how you get on Tom. Kind regards, Gareth. p.s. worth getting the alternator output checked at the same time.
-
Thanks Steve, just been looking at a couple of videos on those. Have to say, all I want is to read codes to identify problems and reset them when the work is done and reset the service indicator. Not worried about accessing special features - well maybe set the one touch indicator function from 3 flashes to 5! - but just want the codes and reset functions so as I can identify problems and sort them. Handily, my local garage just up the road has the VCDS bits and when I pointed out the current 5cm! of ground clearance he said he'd pop down and scan for fault codes.....they've been MoTing and looking after anything I can't do on our cars for 20+ years now so a good relationship there . I'll keep you updated as and when, as I will certainly be asking about parts and general advice ......
-
It's personal preference. There's also obd11 too.
