All Activity

Thank you very much.

Many thanks Antonio, If we haven’t received a response from Andrew by the end of tomorrow, I’ll send him a PM for you, and hopefully post a response. Regards, Gareth.

Thank you very much for your reply. Audi dealership is trying to solve this problem since october 2023. After the diagnosis they find error P044100 - EVAP emission incorrect. The solution was to change N80 valve, but the problem came back! Every 2000km, more or less, the problem returns and i have to stop the car, shut off engine and restart the car so that the system works normally again. I went back to the workshop more than 10 times and they changed practically everything in the EVAP system, but without success. Next appointment at the dealership will be on the 11th. I'm curious about what they'll replace this time...

Hi Roxanne, My investigations showed there are two common faults. The ignition switch and the micro switch which operates on the clutch pedal being depressed. The latter can be on the pedal itself close to where it pivots or it can be on the clutch master cylinder. If you are confident you know what you're doing try my jumper wire mod detailed above. If that works then you know it's not the starter or solenoid. The ignition switch is dead easy to swap. My guess is it's the microswitch on the clutch. It would be dead easy to fit a starter button to get around the issues just power it from an ignition switched live 12V so without the key the starter can be operated. Good luck and please let me know what it turns out to be.

Welcome Antonio, Regrettably Andrew never did return to let the forum know how the issue was resolved. Let’s hope he does now, but if not, you could send him a PM and hope for a response. Regards, Gareth.

Welcome Roxanne and thanks for joining. Since the car won’t crank, it will first need to be established whether the stater motor solenoid is getting a full 12 volts. If it is, suspect the starter motor, if it isn’t, the wiring will need tracing and checking from the ignition/key start to the starter motor. If it were mine, I think I would consider investing in an hours time with a trusted auto electrician. Please let us know how you get on. Kind regards, Gareth.

Hi Same problem. Any update about the solution? Thanks

Hi I am having the same issue a4 b8 won’t crank I have ran diagnostics and got the fault on the picture have tried new relays still nothing… only had the car a couple of month really stressing me out please help when it first happened it did eventually start again after a lot of tries 😕 battery is new and fully charged

Fantastic work, hope you can get it back this week and enjoy it 🙂

As Dave has said it's often a loose wire under the passenger seat.

Welcome Kenny, but please give us some more information for members to go with. Could you please describe the problem you are having? Regards, Gareth.

A little update for you guys. New clutch is fitted, spent about 12 hours all in with two people over two days. Went off without a hitch! Taking off the old clutch made the cause of the noise readily apparent; two of three metal straps holding the pressure plate together was broken! This caused a rough idle and an ungodly rattle with the clutch pedal depressed. Lifted the car by the gearbox side motor mount with an engine lifter and put it on tall jack stands, removed the battery and battery tray. Next we unbolted the wheel well cowling(?)/plastic and the lower control arm for the bushings on the drivers side (Norway so LHD not RHF) so we had space to pull the driveshaft out completely, right hand side driveshaft only need unbolting from the gearbox. After all the bits and bobs on the gearbox was out we dropped it from the bottom with one person underneath. This was a bit finicky but it was enough space to do it without too much trouble. Gearbox oil changed, new clutch slapped on. We didn’t have the tool to compress/pretension the pressure plate so we used a simple centering tool and gradually torqued the screws to 20nm in typical zig zag fashion. With me lying on a creeper/roller and the gearbox on my chest lifted the gearbox and mated it back to the engine with the other person standing above the engine bay and lifting from there. This wasn’t super easy, but a bit of finessing and manouvering of the gearbox did the trick. Highly recommend being two for this job, especially for the mounting and dismounting of the gearbox. The 12 hours includes coffee breaks, googling stuff and a trip to the local parts store. For the algorithm: This was done on a manual 2013 Audi A3 8V 1.4 TFSI CMBA 122bhp engine, gearbox code is MYF/0AJ.

Looking at it closely I think it's just staining and not actually a deep crack , it's like the edges of wet staining. The car is driving to well for me to believe that the gearbox is cracked, When I look there is no sign of oil leaking down from the marks . That surly would suggest that it's not leaving oil out .

Also the car is driving perfect, no skipping gears , smooth gear changes , everything seems normal .

Did a bit of further investigation and something the scares the s**t outta me , what looks like a small hairline crack along the metal over the plastic sump , it doesn't look like oil is leaking out of it looks dry around it , can these cases get small hairline cracks that don't go the whole way through , so they actually don't leak ? Surely the would be fluid marks running down from the crack , and there is also never oil on ground underneath the sump

Hi everyone!! We can help with updates and activations by software. Send us your VIN and your software version 😁👍 You also can find us here: https://www.instagram.com/codigos_spain92 All in remote work!!

Hi. If you have any issues with insurance at all for an imported vehicle then please feel free to drop me a line. Regards, Dan.

This is brilliant work

Hi guys, this is my first time joining, and my first time posting. Definitely won’t be my last time. This is because I just recently picked up an Audi a4 B8 saloon 2008 and I’m loving it apart from some problems which I’m trying to solve. I do things myself DIY, and I need guidance for this issue. I will attach a link from my YouTube with this issue. Whenever I turn the wheel I hear a clunk from inside the car I’m not sure what it is. I’ve read multiple different opinions based on what it is but I’m hoping for some more help. Any help would be so appreciated. Thank you so much. I’m still getting used to this platform so if I take time responding, please bear with me thanks again guys

Hello Frank, Well worth searching EBay. Please let us know how you get on. Regards, Gareth.

Hi, i have a problem with my AC, i have a fault code, as anyone seen this before E.PA.RPC.71 (2505311808)

I am not aware of alarms for gearbox oil level, only for engine oil level, but maybe I am out of date on that score. Maybe somebody else will chip in with an opinion.

I’m still learning “to drive” this forum and don’t know how to search it yet lol

Yes the reflectors are fine and lenses are pretty clean there is no “smoke stain” (all I can think of explaining what I mean) on inside face of glass. I will order new bulbs at least then I know they are ok thanks again for your time 👍

Smiles your not wrong it already looks so much better happy days