Jump to content


Smyth Ute S4 B6 Build Diary


NoggyMatt
聽Share

Recommended Posts

Hi all I am just starting my smyth ute build and thought I would put a build diary up.

Car is: 2004 Audi S4 B6 in silver, 90,000 miles, it like all cars this age it needs some loving 馃. So yesterday I started to strip the rear ready聽for the cuts, Rear seats out,聽all rear trim, lights and curtain airbag' s, also labelling all wires and connectors,聽here is a few pictures.

Screenshot_20200815-114301_Facebook.jpg

20200824_113712.jpg

20200824_122608.jpg

Screenshot_20200815-114216_Facebook.jpg

20200824_113649.jpg

20200824_122621.jpg

20200824_130404.jpg

20200824_130353.jpg

20200824_122659.jpg

20200824_123002.jpg

Screenshot_20200815-114231_Facebook.jpg

20200824_122815.jpg

20200824_134117.jpg

20200824_144821.jpg

20200824_122713.jpg

20200824_144811.jpg

Screenshot_20200815-114256_Facebook.jpg

Screenshot_20200815-114204_Facebook.jpg

Link to comment
Share on other sites


Bumper is off and the tubing/hose聽goes into the rear bumper from the blue vaccum cylinder聽 and tees off into 2 lines, then just ends and hangs loosely at the bottom of the bumper and someone has capped them off with 2 screws ( see pictures ). Am I right in thinking that these lines went to the old oem exhaust to control the flappers????

20200825_130142.jpg

20200825_130240.jpg

20200825_131313.jpg

Link to comment
Share on other sites

Got the doors off, Boot/trunk off, car is completely stripped in the rear now and every single wire, connector all labled, And got all the measurements marked out ready for my fresh eyes to double check it all again tomorrow, measure twice, cut once as my old grandad used to say. And I got the call from shipping agent to say my kit is ready to collect tomorrow morning from 8am.
So a very productive day.

20200826_162359.jpg

20200826_161746.jpg

20200826_162428.jpg

20200826_161733.jpg

20200826_162411.jpg

20200826_162129.jpg

20200826_162113.jpg

20200826_162443.jpg

20200826_162155.jpg

20200826_162143.jpg

20200826_162242.jpg

20200826_162217.jpg

20200826_125605.jpg

20200826_162345.jpg

20200826_162300.jpg

20200826_125618.jpg

Link to comment
Share on other sites

3 minutes ago, Steve Frost said:

Hi Matt,

Wheels look a good choice. They will suit the Ute.聽

Thanks Steve, they need a refurb first and some new tyres, did you find your black TT handles??

Link to comment
Share on other sites

No came by boat, and when unloading the amount of people asking if there was a body in it lol, have you put a ad in the wanted section on here?, MIT have some luck, or is there no way of getting them painted?, mite be cheaper than buying and fitting new handles.聽

Link to comment
Share on other sites

So yesterday was just a tidying up and getting ready for the final cuts, checked all the measurements probably 10 times 馃馃お.
Today it took an hour as a raven decided to perch it's self on the Audi roof and would not shift, 聽I got all the final cuts done and sanded back to the line and hovered all the metal filings up with a paint brush and hover to cut the risk of rusting later down the road. It needs some rust preventative over it and a bit of paint.

20200830_160037.jpg

20200830_160256.jpg

20200830_160046.jpg

20200830_155945.jpg

20200830_160251.jpg

20200830_160224.jpg

20200830_160026.jpg

20200830_160022.jpg

20200830_160147.jpg

20200830_160100.jpg

20200830_160050.jpg

20200830_160115.jpg

Link to comment
Share on other sites

14 minutes ago, Steve Frost said:

Probably a crow unless you've moved to Wales.聽

Everyone was adamant it was a聽raven we had about 10 people stop and take pictures, phoning wildlife trust, rspca, and it seemed very domesticated towards men that went up to it, they think it's got out from somewhere maybe?

Link to comment
Share on other sites

B pillar loosely fitted with a few rivets, and test fitted the front wall, front tray, and bed sides, I had to make a few tweeks to the bolt holes so the bed sides sat flush front and back and also followed the lines over the inner wheel arches, i have a few gaps in places as shown in the pictures. Apart from them it all sit nicely.

20200904_144948.jpg

20200904_144747.jpg

20200904_181720.jpg

20200904_144708.jpg

20200904_181421.jpg

20200904_144651.jpg

20200904_144808.jpg

20200904_144801.jpg

20200904_144507.jpg

20200904_144827.jpg

20200904_144820.jpg

20200904_144532.jpg

20200904_144903.jpg

20200904_144516.jpg

20200904_144841.jpg

20200904_144620.jpg

20200904_144938.jpg

20200904_144548.jpg

20200904_144915.jpg

Link to comment
Share on other sites

A quick update, I have not done much over the past week as back at work馃お, still in the test fit stage but going wel, ( with the help from the UTE guru's on here. Thank you all again. )
All my tailgate gaps are equal. (Very surprised),
It all straightened it's self up once I put the long wooden spacer in at the top of the tailgate, door gaps are near on equal with just minor adjustments needed. This morning I have been cutting and messaging the rear window surround in place, it is now sitting under the door rubbers and lined up with the fold impression line on the top wall. I'm just not to sure about the bottom corner that sits on the rear grander panels, it won't sit flush, I have sanded a bit but do not want to go to far.

20200914_141626.jpg

20200914_141319.jpg

20200914_141304.jpg

20200914_141147.jpg

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

聽 Pasted as rich text. 聽聽Paste as plain text instead

聽 Only 75 emoji are allowed.

聽 Your link has been automatically embedded. 聽聽Display as a link instead

聽 Your previous content has been restored. 聽聽Clear editor

聽 You cannot paste images directly. Upload or insert images from URL.

聽Share






  • Create New...

Forums


News


Membership


  • Insurance
  • Support