Leaderboard

From all the admin team Just want to wish all our members a happy Easter 🐰🐣 hope you have a great day 😊

Thanks for being in touch Linds. When you say your small garage tightened the belt, and it now makes a noise - concerns. I’m also intrigued to work out how you actually know the belt is tighter than it was. If (in caps) the belt is tighter than it should be, are you happy to entrust the fitting of a new belt and assembly to them? Water pump? - if cambelt driven on your engine. Wondered what you propose to do about that. Kind regards, Gareth.

Hi All just thought id share if it already hasn't been i lost power to my front doors no windows worked wing mirror stopped and central locking to drivers door, so after stripping own the dash under the wheel to get to the fuse box to check all wires and taking the door cards of and looking couldn't find any damaged wires it turns out that it was the ground wire to the module in the door that had dis connected somewhere in the rum so ive snipped it and joined a new wire to a bolt that has a ground in the door all working again now . just thought i would share in case someone else has this problem

Just to say that I bought a space saver 19" wheel from The Wheel Shop along. As Stevey noted above, I then stuck several sections of polystyrene using gaffer tape (pic 1) to support the wheel and keep it off the battery cables to the left and right. Enough space underneath the wheel to store the compressor and tyre repair bottle (pic 2) (just in case). This raised the spare wheel but there was still just enough thread available on the centre to allow me to use the normal large plastic nut to hold the spare in place (pic 3). Although the spare was a little higher than normal due to the polystyrene, there's still enough space to allow the top cover to sit flat in the boot. Lastly the tools including jack fit in the plastic tray (pic 4) between the battery and the back of the rear seats (blue towel round them to stop rattling).

Hi all, I came across an issue recently that appears common enough for people to post with requests for solutions but unusually where I failed to find a concrete fix. So here is my stab at this: The other week I went to do an oil check, pulled the bonnet release level and to my dismay felt no resistance and the bonnet remained firmly shut. Bugger – how to get the bonnet open? There is no access from the front – even destroying off the plastic grill will not get you to any bolts that will help. What is the solution without resorting to a can opener and consequentially a new bonnet?? Here it is… It will be much better to download the attached pdf as this has pics that will help a lot, but instructions with no pics are: 1. Go to B&Q (or equivalent hardware store) and purchase a 4-6mm diameter steel rod between 70 cm and a meter in length. Mine cost £2.60!!! 2. Get a decent vice and make two 90-degree bends at each end of the rod about 10 cm from end of rod by hand (I off-set each end by 90 degrees approx.), to make a ‘emergency bonnet release tool’. 3. Get the front of the car on ramps or jack up as high as possible. Remove undertray and get a good torch and get underneath…. 4. You need to locate the bonnet lock mechanism – it’s at the top of the radiator fans. It will be very hard to see… From below, at the right angle, you should be able to see the underside of the lock mechanism look for the large spring. 5. The reason you are unable to open the bonnet might be: 1, the cable has snapped; or 2, (as in my case) the end of the cable has come lose from the lock mechanism. The 2nd issue is common if you have had the front off and lock carrier into the service position and the cable-end has not been seated back in properly… 5. There are actually 2 sites for a cable to connect. If you have a RHD vehicle then the cable seats into the lower slot; if a LHD then upper slot. You need to get the end of your ‘emergency bonnet release tool’ into one of these two slots, and then twist using the lock housing to lever off and move the release mechanism. If you get into the lower slot the twist right; if you get into the top slot, then twist left. If you use a tube spanner or the end of a ring spanner to get on the other end of the rod where the other 90-degree bend is then you get more force and the bonnet should open! Brilliant. 6. I then decided to add a bit of thick plastic cut to size to cover the cable end housing to stop it coming out again. Drill a small hole and tap a screw into it but do not tighten yet. 7. Reinstall the lock, and reseat the cable end properly, then swing the plastic down over the cable end and tighten screw. Not sure if this will work/last, but at least you now have an ‘emergency bonnet release tool’ to sort it… Hope this is of some help…. Bonnet open solution.pdf

Oh Father in Law!

Hi, as long as the cables for the extra battery don't go inside the wheel tub you should be fine measure the O/D of your existing wheels on your car and marry that against the I/D of the wheel tub, the moulding for the cr@p inflation system is removable and just leaves you the threaded spigot which will anchor your space saver, you can get round the possible noise of the wheel against the floor by buying some cheap stick on insulation, about 4mm thick from eBay and sticking it around the tub, if you mount the wheel face down you can use the space inside the wheel for your jack wrapped in an old towel or similar, just did this on my new Passat cab and found to my joy that the wheel tub was deep enough to take a full size spare. Steve.

Hi Gareth I appreciate your sentiment but realistically I doubt it will make a difference to more than a minority as most of these one post wonders can't even be bothered to look through the legions of post on this wonderful site to see if there is already an answer to their question, NO its far easier just to wait for some poor soul to to spoon feed the answer to them, I find this situation intolerable and on a personal level endorses my opinion that charging a small joining fee would eradicate the free loaders and any funds gathered from serious users would help with the costs of this forum, I have joined a few forums in my time and all required a subscription with the exception of some Ford forums, over the last couple of years the formulae for this situation has become blindingly apparent these people buy these cars in the blind belief that the Audi never goes wrong, someone told them that and its what they wanted to hear, most of the members on here all know that statement to be far from the truth, thats why they are here and after their own problems are solved actively engage in trying to help others, I have noticed lately that a couple of new members have posted the problem and the solution to that problem that they have worked out for themselves, we could definitely do with more members with that mind set. Steve.

Post and run! Joined April 3rd - posted plea for help on April 3rd - not returned since to review any responses. Time taken to construct replies is free of charge, but it is time consuming! Best we can hope for is the information maybe of help to others.

Unless the power steering emis whining etc id say it's normal compared to new cars.

Kat. Who or what is telling you that the ABS module is faulty? The dashboard lamp, a proper VAGCOM diagnosis, a cheap code reader, a mechanic, or something else?

Is it worth considering the abs sensors? As they're cheaper to replace before changing the module

https://www.google.com/search?q=audi+a6+gearbox+code+QLX.&oq=audi+a6+++gearbox+code+QLX.&gs_lcrp=EgZjaHJvbWUyBggAEEUYOTIGCAEQRRg80gEJMTA3MGowajE1qAIAsAIA&sourceid=chrome&ie=UTF-8

happy easter to all the admin thank you for all your time and effort best wishes stephen😁

Hi Sean, I ended up finding the LUK 0B2105266T flywheel on ebay for £300 brand new. The garage removed the old clutch and said it was a Sachs after all… but they put the LUK flywheel in with LUK clutch plate kit clutch has been in nearly 12 months or so and all is well! Had timing belt and water pump done at the same time. I did have a bit of trouble after as the garage said they nudged an EGT sensor when removing the clutch assembly. Car ended up going into limp mode with the coil light and DPF warning coming on. New sensor sorted that.

those error messages are in fact a frequent thing and it comes down to the sensitivity of your settings (radar, collision assist etc). You can adjust your settings to pick up far less in the realms or items vs distance but not recommended. FYI the car records loss of vision or detection as faults and stay logged until removed. I recently had Audi assist come out for something else related I had 136 codes stored and following that CAM bus errors because of how many were stored. I was politely reminded that these issues have become a common issue causing modules to slow down or self fault due to bus memory being clogged with error codes. from time to time it’s recommended to review and clear. Ideally around service intervals. You’d think your main dealer would do this as part of their service but they don’t and leave them…

Finally this issue has been explained in a simple manner. I've been chasing a leak in my GTI with the same engine and haven't found anyone explain it the way you did. Thanks for this and I did subscribe and like this! Thanks man, take care Kodi

Further update on the 7 Speed S-Tronic DL-501 issue ...... I haven't been able to get the adaption re-done yet after the full gearbox and both filters service as Matt with VCDS has been incredibly busy with his day job, but the one thing I will say after using the car for a few weeks now is it is incredibly smoother than it was before the service and the first VCDS mild adaption, no longer does it thump from second to first and even in reverse there seems to be a definite difference in the take up of the gear, especially on a slope, something it didn't like doing at all before the service, I am genuinely surprised how fresh filters and proper manufacturer recommended "MEYLE" DSG OIL can make that much of a difference, I haven't taken it on a long run yet and got everything in the gearbox up to a constant temperature and speed but around town driving is noticeably much smoother. As it started to fail on me and throw the dreaded yellow warning light on the dash after long motorway cruising I don't want to count my chickens too soon, but I'm hopeful that with a final and Full VCDS Gears Adaption my problem may well be pretty much sorted, as usual will keep posting updates for other members ......... 🤔

Turns out the Haynes book threw me a red herring on the ACE engine the mid shaft only runs the oil pump, therefore no need to have a timing point on the cog. I found this out after rotating it with my hot wire rig setup but nothing was happening and the wires to the coil from my golf were getting hot. I even took off the distributor cap and sure enough the arm was not moving. Even I found another string on the net that has a sketch of a hole by the bell housing that should show a timing mark, however that was not moving. Then I went back to Haynes and looked up distributor where I found, I quote “ACE and AAR engines, the distributor is located on the right hand of the engine and is driven off the rear of the camshaft. After finding out my cam belt was 2 teeth out, I put all back together again, indecently the distributor cap had a mount bolt loose, that would not help. I manually cranked the engine over, no issues. Started on the button idled fine up to 60 degrees where the engine started to search again, but not as bad as before. I just instinctively unplugged the isv and she purred like a cat at just over 1k and was rock solid, plugged isv back in and the searching came back, new one on order. I turned off the car, and waited 5 minutes but she would not fire up. Back to Haynes for inspiration and eventually I found a problem that I feel is the root cause,…. The connector on the loom to Part OEM 034919369C has been wired wrongly, not only that somebody tried to correct the fault by forcing the two parts upside down and the new connector is also broken. I have found a you tube person who prints new ones as the connector is no longer available. 3-pin connector 893971974. Has anyone got a wiring diagram for the correct wires to locations they could show to me so I can get this faux pas sorted out. I feel close to getting this car running the way she should again, what an interesting day I have had.

Yes I had a lot of trouble trying to get the service history off them. They kept saying they couldn’t get hold of it as they were not the registered keeper Will follow your advice for future purchases. Thanks again.

Glad you got sorted 🙂

Really not sure. Will keep you posted if I get it sorted

I solved the vibration of the airbag at low revs by lining the space under the airbags with this packing foam. It's quiet for now. 🙂

Well i finally got my coolant leak issue resolved. Hose and seal issues. So extended warranty wouldn't cover it. Dealer said they will cover costs as gesture of good faith. ( i did wait a while for an appointment) I am pleasantly surprised, and faith in the dealers has been considerably restored. Any other pleasant dealership stories out there.

Hi Andy unfortunately not, Audi have all the codes for every model from 2011 up and wont supply that information to any outside key suppliers, its not like the old days when you got a dummy key and just coded the new transducer in that key via the ignition. Steve.

Ok thanks for reply. Took it to main dealer and of course diagnostic test did not reveal malfunction so advised to monitor it. However, later I did notice that if I pull handle hard it seems to stop it from locking but I still do not think this should be necessary so will see how it goes.

Welcome Alberto, Are you saying you and/or your son are capable of safely renewing brake pads? It seems you have already bought replacement pads. Since the seller seems disinterested in sorting it out, why not carry out your own assessment of the remaining brake pad thickness, and simply renew them - since you have them. Worse possible case:- brake pad wear light remains on after you have done that -? Worry about sorting that out when you get to that point. Perhaps you could let us know how you get on. Kind regards, Gareth.

Audi have replaced the drivers door latch under warranty part no. A4K2 837 016 H the car still at Audi checking hand brake .

Oil level sensor Paul?

Audi Coventry run the diagnostics and found no faults. So I went to Rugby services to try their 350kwh charger... and it charged perfectly. Then I realised that the charger cable was on the right and plugged easily into the DC charging port on the right (drivers) side of my etron as I had entered the bay nose first. I recall the chargers that had been problematic at Woolley Edge and Wetherby had cables on the left side and it was quite a stretch to drag them across the bonnet to plug in as they wanted to retract. So I surmise that was the issue i.e. the charging cable was not properly seated. Next time I will reverse in if I use these chargers.

Loving those wheels 👍

Good Morning I have a partition net/dog guard ( part number 4G9 861 691 94 H) suitable for A6 Avant. Free of Charge if anybody would like it. Also I have an Autochair mobility scooter hoist for the A6 Avant. Cost £1400 also free of charge, this comes with modified rear boot screen and side panel, to anybody who needs it. Tony

I have a fix. I also own a mk2 Golf and I spotted a detail on the gas peddle cable that is the same for adjustment, at the end there is a castellated section with a clip on it for tension, I added a couple of castellations to the tension and I now have 1k solid tickover. 😁 The clip sinks into the rubber grommet, lowering the tension over time. 😎

Yes agree re navigation software. I do know the Audi garage did update the software including MMI software but whether that is latest (unlikely) is anybody's guess and was just pleased I could use android auto wirelessly (plus fixing maps / navigation issues). The only OTA updates I have seen are for the navigation maps and each of those has been successful. If you are picking up from a dealer I would ask them to sort it out for you - I know mine have been great when I have asked them.

I'd recommend a diagnostic check to see if any fault codes flag up. If you've bought it from a dealer then they have to fix it foc in the first 30 days from sale as you're still entitled to a full refund within that time.

Hi on the other hand you could just try converting it to standard shocks if you only buy one side thats a no,no as shockers are always replaced in pairs, I found shocks on eBay that came with the caps for far less than the price for just one, standard shocks give you the option of Bilstein, Monroe, Sachs which are all the same if not better. Mag ride is a gimmick that sounds wonderful in theory but its only an electrical current passed into the oil which makes the metal floating in the oil bond so it gives the relief valve a far greater volume to deal with therefore stiffening the flow, Monotube shocks are far better as they are gas over oil and give more progressive damping and better tyre contact, can't beat a bit of Bilstein. Steve.

Will do, looking forward to getting it back but I feel my ownership may not last long at this point as garage has advised me to get fixed and get gone, but that would mean I’d lose a fair bit in the short time I’ve had it, and I’d just put 4 new tires on.

The low oil consumption suggests the engine is in reasonable condition for its age, and in standard form would likely not have high CO emissions. Therefore I'd say your modifications are responsible for the problem, and the solution is to restore the engine to standard form.

Yea an Audi independent is an option or an auto electrican

Hi Dan. I would think paint would last that long being bombarded by grit off the road. But, you can buy a proper black surround and grill for the A3 from E Bay for £120. Tony

It could be a back tyre issue, or any of a dozen different issues from the sparse information you have provided. Whatever the cause, if you bought the car recently take it back to the dealer you bought it from.

Hello Nick, As Stevey says. I been putting a dampener on anything to do with large wheels for some time, since the trend seems to be for the largest wheels and the skinniest tyres - because they look good. Yet, you cannot see the wheels when you are sat in the car, but you are the one who suffers the adverse ride quality. Add to the potential of harder sidewalls, probably XL etc. and everything gets magnified. An equally aged friend found the ride to be not to his liking on an S.Line with skinny tyres chosen for him by his children - it went back. Mind, I’d not be too happy about the expense of changing wheels and tyres, but… Interesting you mention Bridgestone, since I have been considering these on our non-Audi. For me, I want as comfortable ride as I can get from the tyres, and as much mileage as poss. so any recommendations are welcome. Kind regards, Gareth.

Thanks Les -? Saying it as it is, the only clue you give us is that it’s a stop/start battery, and regrettably you have chosen/can’t be bothered to, either give your name, model of car or your location. As one of the other moderators often says ‘ we are a friendly and helpful group’, and indeed we are, but….. help yourself to gain the help you need! Rant over, except a please or thank you wouldn’t’ go amiss. Answer - almost certainly yes.

Hi its the thermostat on the water pump that controls the engine temp the other one before the the heater is the one that controls the cabin temp, if that one is playing about all your hot water flies through the bypass system. Steve.

Hello Thomas, I guess you have a conventional manual handbrake, by the year of the car. Assuming the pads and calipers are in a serviceable condition, then it maybe wise to totally slacken handbrake adjustment to a point where the cables can be disconnected at both wheels. You can then sharply apply the footbrake and ensure both rear wheels lock up properly and then fully release properly. It would be great if your friendly MOT station could retest the rear brake efficiency and balance to ensure they are working properly - oops, just realised Ireland - so Government testing?? Once you have established correctly working rear wheel braking , you can then tackle the handbrake cable efficiency. Do both cables pull and release properly? Renew if any doubt. Your A4 may have the same set up as the similar year A3, whereby the cables pass through aluminium guide tubes, and they can stick within these tubes. New tubes will be necessary and I think these are main dealer parts only. Liberal application of WD40 may assist handbrake cable action and removal of tubes if necessary. Kind regards, Gareth.

And no vibration at the steering wheel or pedals? In that case I would look to the rear tyres being damaged or out of balance as the most likely candidate. That does not rule out other possibilities such as worn wheel bearings, loose wheel nuts, warped brake discs but they wou;d cause symptoms that you have not mentioned.