Leaderboard

From all the admin team Just want to wish all our members a happy Easter 🐰🐣 hope you have a great day 😊

Thanks for being in touch Linds. When you say your small garage tightened the belt, and it now makes a noise - concerns. I’m also intrigued to work out how you actually know the belt is tighter than it was. If (in caps) the belt is tighter than it should be, are you happy to entrust the fitting of a new belt and assembly to them? Water pump? - if cambelt driven on your engine. Wondered what you propose to do about that. Kind regards, Gareth.

Hi All just thought id share if it already hasn't been i lost power to my front doors no windows worked wing mirror stopped and central locking to drivers door, so after stripping own the dash under the wheel to get to the fuse box to check all wires and taking the door cards of and looking couldn't find any damaged wires it turns out that it was the ground wire to the module in the door that had dis connected somewhere in the rum so ive snipped it and joined a new wire to a bolt that has a ground in the door all working again now . just thought i would share in case someone else has this problem

Just to say that I bought a space saver 19" wheel from The Wheel Shop along. As Stevey noted above, I then stuck several sections of polystyrene using gaffer tape (pic 1) to support the wheel and keep it off the battery cables to the left and right. Enough space underneath the wheel to store the compressor and tyre repair bottle (pic 2) (just in case). This raised the spare wheel but there was still just enough thread available on the centre to allow me to use the normal large plastic nut to hold the spare in place (pic 3). Although the spare was a little higher than normal due to the polystyrene, there's still enough space to allow the top cover to sit flat in the boot. Lastly the tools including jack fit in the plastic tray (pic 4) between the battery and the back of the rear seats (blue towel round them to stop rattling).

Hi all, I came across an issue recently that appears common enough for people to post with requests for solutions but unusually where I failed to find a concrete fix. So here is my stab at this: The other week I went to do an oil check, pulled the bonnet release level and to my dismay felt no resistance and the bonnet remained firmly shut. Bugger – how to get the bonnet open? There is no access from the front – even destroying off the plastic grill will not get you to any bolts that will help. What is the solution without resorting to a can opener and consequentially a new bonnet?? Here it is… It will be much better to download the attached pdf as this has pics that will help a lot, but instructions with no pics are: 1. Go to B&Q (or equivalent hardware store) and purchase a 4-6mm diameter steel rod between 70 cm and a meter in length. Mine cost £2.60!!! 2. Get a decent vice and make two 90-degree bends at each end of the rod about 10 cm from end of rod by hand (I off-set each end by 90 degrees approx.), to make a ‘emergency bonnet release tool’. 3. Get the front of the car on ramps or jack up as high as possible. Remove undertray and get a good torch and get underneath…. 4. You need to locate the bonnet lock mechanism – it’s at the top of the radiator fans. It will be very hard to see… From below, at the right angle, you should be able to see the underside of the lock mechanism look for the large spring. 5. The reason you are unable to open the bonnet might be: 1, the cable has snapped; or 2, (as in my case) the end of the cable has come lose from the lock mechanism. The 2nd issue is common if you have had the front off and lock carrier into the service position and the cable-end has not been seated back in properly… 5. There are actually 2 sites for a cable to connect. If you have a RHD vehicle then the cable seats into the lower slot; if a LHD then upper slot. You need to get the end of your ‘emergency bonnet release tool’ into one of these two slots, and then twist using the lock housing to lever off and move the release mechanism. If you get into the lower slot the twist right; if you get into the top slot, then twist left. If you use a tube spanner or the end of a ring spanner to get on the other end of the rod where the other 90-degree bend is then you get more force and the bonnet should open! Brilliant. 6. I then decided to add a bit of thick plastic cut to size to cover the cable end housing to stop it coming out again. Drill a small hole and tap a screw into it but do not tighten yet. 7. Reinstall the lock, and reseat the cable end properly, then swing the plastic down over the cable end and tighten screw. Not sure if this will work/last, but at least you now have an ‘emergency bonnet release tool’ to sort it… Hope this is of some help…. Bonnet open solution.pdf

Oh Father in Law!

Hi, as long as the cables for the extra battery don't go inside the wheel tub you should be fine measure the O/D of your existing wheels on your car and marry that against the I/D of the wheel tub, the moulding for the cr@p inflation system is removable and just leaves you the threaded spigot which will anchor your space saver, you can get round the possible noise of the wheel against the floor by buying some cheap stick on insulation, about 4mm thick from eBay and sticking it around the tub, if you mount the wheel face down you can use the space inside the wheel for your jack wrapped in an old towel or similar, just did this on my new Passat cab and found to my joy that the wheel tub was deep enough to take a full size spare. Steve.

Hi Gareth I appreciate your sentiment but realistically I doubt it will make a difference to more than a minority as most of these one post wonders can't even be bothered to look through the legions of post on this wonderful site to see if there is already an answer to their question, NO its far easier just to wait for some poor soul to to spoon feed the answer to them, I find this situation intolerable and on a personal level endorses my opinion that charging a small joining fee would eradicate the free loaders and any funds gathered from serious users would help with the costs of this forum, I have joined a few forums in my time and all required a subscription with the exception of some Ford forums, over the last couple of years the formulae for this situation has become blindingly apparent these people buy these cars in the blind belief that the Audi never goes wrong, someone told them that and its what they wanted to hear, most of the members on here all know that statement to be far from the truth, thats why they are here and after their own problems are solved actively engage in trying to help others, I have noticed lately that a couple of new members have posted the problem and the solution to that problem that they have worked out for themselves, we could definitely do with more members with that mind set. Steve.

Post and run! Joined April 3rd - posted plea for help on April 3rd - not returned since to review any responses. Time taken to construct replies is free of charge, but it is time consuming! Best we can hope for is the information maybe of help to others.

Unless the power steering emis whining etc id say it's normal compared to new cars.

Kat. Who or what is telling you that the ABS module is faulty? The dashboard lamp, a proper VAGCOM diagnosis, a cheap code reader, a mechanic, or something else?

Is it worth considering the abs sensors? As they're cheaper to replace before changing the module

https://www.google.com/search?q=audi+a6+gearbox+code+QLX.&oq=audi+a6+++gearbox+code+QLX.&gs_lcrp=EgZjaHJvbWUyBggAEEUYOTIGCAEQRRg80gEJMTA3MGowajE1qAIAsAIA&sourceid=chrome&ie=UTF-8

happy easter to all the admin thank you for all your time and effort best wishes stephen😁

Hi Sean, I ended up finding the LUK 0B2105266T flywheel on ebay for £300 brand new. The garage removed the old clutch and said it was a Sachs after all… but they put the LUK flywheel in with LUK clutch plate kit clutch has been in nearly 12 months or so and all is well! Had timing belt and water pump done at the same time. I did have a bit of trouble after as the garage said they nudged an EGT sensor when removing the clutch assembly. Car ended up going into limp mode with the coil light and DPF warning coming on. New sensor sorted that.

Hi its the sealing ring, most likely they did not change it with the unit problem being that you have to buy the seal separately and they are quite expensive, its either the seal or they have damaged the locking ring that holds the pump in when they re tightened it, the third hole looks like a breather, easiest way to check is get a small length of wire and push it into the hole and see if it bottoms out, if it does its the seal. Steve.

Pic 1 for sure

Turns out the Haynes book threw me a red herring on the ACE engine the mid shaft only runs the oil pump, therefore no need to have a timing point on the cog. I found this out after rotating it with my hot wire rig setup but nothing was happening and the wires to the coil from my golf were getting hot. I even took off the distributor cap and sure enough the arm was not moving. Even I found another string on the net that has a sketch of a hole by the bell housing that should show a timing mark, however that was not moving. Then I went back to Haynes and looked up distributor where I found, I quote “ACE and AAR engines, the distributor is located on the right hand of the engine and is driven off the rear of the camshaft. After finding out my cam belt was 2 teeth out, I put all back together again, indecently the distributor cap had a mount bolt loose, that would not help. I manually cranked the engine over, no issues. Started on the button idled fine up to 60 degrees where the engine started to search again, but not as bad as before. I just instinctively unplugged the isv and she purred like a cat at just over 1k and was rock solid, plugged isv back in and the searching came back, new one on order. I turned off the car, and waited 5 minutes but she would not fire up. Back to Haynes for inspiration and eventually I found a problem that I feel is the root cause,…. The connector on the loom to Part OEM 034919369C has been wired wrongly, not only that somebody tried to correct the fault by forcing the two parts upside down and the new connector is also broken. I have found a you tube person who prints new ones as the connector is no longer available. 3-pin connector 893971974. Has anyone got a wiring diagram for the correct wires to locations they could show to me so I can get this faux pas sorted out. I feel close to getting this car running the way she should again, what an interesting day I have had.

Hi I would definitely get some body in that line of work to look at it and tell you realtime what's been done, never been a fan of mapping as half the clowns out there have no idea what they are doing or what the long term implications of their work is, are you still getting codes? Steve.

A(nonymous). Given that this thread is over seven years old it is unlikely you will get a response from the originator. Nevertheless there are some useful suggestions in it. Have you tried any of them?

Yes I had a lot of trouble trying to get the service history off them. They kept saying they couldn’t get hold of it as they were not the registered keeper Will follow your advice for future purchases. Thanks again.

Glad you got sorted 🙂

I solved the vibration of the airbag at low revs by lining the space under the airbags with this packing foam. It's quiet for now. 🙂

Well i finally got my coolant leak issue resolved. Hose and seal issues. So extended warranty wouldn't cover it. Dealer said they will cover costs as gesture of good faith. ( i did wait a while for an appointment) I am pleasantly surprised, and faith in the dealers has been considerably restored. Any other pleasant dealership stories out there.

Hi Andy unfortunately not, Audi have all the codes for every model from 2011 up and wont supply that information to any outside key suppliers, its not like the old days when you got a dummy key and just coded the new transducer in that key via the ignition. Steve.

Welcome Alberto, Are you saying you and/or your son are capable of safely renewing brake pads? It seems you have already bought replacement pads. Since the seller seems disinterested in sorting it out, why not carry out your own assessment of the remaining brake pad thickness, and simply renew them - since you have them. Worse possible case:- brake pad wear light remains on after you have done that -? Worry about sorting that out when you get to that point. Perhaps you could let us know how you get on. Kind regards, Gareth.

Audi have replaced the drivers door latch under warranty part no. A4K2 837 016 H the car still at Audi checking hand brake .

Getting my lock system replaced at the local Audi garage on my A6 2021 .. had the same problem

Welcome Fi, and thanks for joining. First things first:- Can we take it you have studied copy of the on-line MOT history for this car? Also, have you seen evidence of its service history? Have you done an on-line DVLA Vehicle Check to see when the last V5 was issued? This will give you some idea of how long the last owner has owned it? Short ownership - possibly not good. Down to specifics:- Water leaks- search the forum for issues and possible solutions. Panoramic roof - potentially a problem area due to generally non solvable leaks. Personal view ( pardon the pun!) I wouldn’t be interested. Hopefully owner members will fill in the remaining answers for you. Hope some of this helps, Kind regards, Gareth.

Hi , 2017 a6 with the same leak on both sides of the car , running down A frame and into foot well . The water as I'm sure is the same for most gets in where the water flow / level becomes to much for the drain and builds up ( doesn't take much ) it overflows to the inside of the wind defector and the leak gets in where there is a steel spring finger . Water gets in where it locates towards the front .... BUT regardless of that , iv found at the rear of the spring finger , under hole is a 10mm × 10mm square hole in the frame on both sides which flows directly in onto the headliner. Joke of a design. I'm working on a fix at the minute 🤞

Hello Jay, The definitive answer lies in the build record, and you should be able to obtain this from Audi Cust. services, or possibly through a dealer - both through the VIN. Possible theory:- delayed release due to the chip crisis?? Kind regards, Gareth.

Audi Coventry run the diagnostics and found no faults. So I went to Rugby services to try their 350kwh charger... and it charged perfectly. Then I realised that the charger cable was on the right and plugged easily into the DC charging port on the right (drivers) side of my etron as I had entered the bay nose first. I recall the chargers that had been problematic at Woolley Edge and Wetherby had cables on the left side and it was quite a stretch to drag them across the bonnet to plug in as they wanted to retract. So I surmise that was the issue i.e. the charging cable was not properly seated. Next time I will reverse in if I use these chargers.

Ditto what Gareth wrote. Let me add that it is always wise to change the water pump belt at the same time as the cambelt because the same expensive work is needed to access them both.

You quote "same model as you" the 80 wing is the same across the 80 B4 range, including saloon, ragtop and Avant to be precise part number is 8A0821106. You quote "not requiring any paintwork rectification" This is something you have said, not me. Other than that, thank you for your wishes Gareth.

Yes agree re navigation software. I do know the Audi garage did update the software including MMI software but whether that is latest (unlikely) is anybody's guess and was just pleased I could use android auto wirelessly (plus fixing maps / navigation issues). The only OTA updates I have seen are for the navigation maps and each of those has been successful. If you are picking up from a dealer I would ask them to sort it out for you - I know mine have been great when I have asked them.

I'd recommend a diagnostic check to see if any fault codes flag up. If you've bought it from a dealer then they have to fix it foc in the first 30 days from sale as you're still entitled to a full refund within that time.

Problem resolved. I replace the tailgate lock. My conclusion is that the lock did not "signal" door open and this causes the towbar to not release etc....

The low oil consumption suggests the engine is in reasonable condition for its age, and in standard form would likely not have high CO emissions. Therefore I'd say your modifications are responsible for the problem, and the solution is to restore the engine to standard form.

Hi its quite a common problem mostly the rubber bit rotting out but if I were you I would take heed of the term not seriously weakened, get under the back clean the alloy bit with a small wire brush and then give it a coat of Waxoyl that will keep the rot at bay for years, did mine when I first got it 2019 and they were still good four years later. Steve.

Hi, I had the same problem on my 2017 a4 allroad last year, same place, o/s/r lower, I had mine replaced at an independent v w garage at just over £100. p.s. my brother, who has the identical car had his go as well on the o/s/r/ seems funny it is always the o/s/r. that goes.

Thanks Les -? Saying it as it is, the only clue you give us is that it’s a stop/start battery, and regrettably you have chosen/can’t be bothered to, either give your name, model of car or your location. As one of the other moderators often says ‘ we are a friendly and helpful group’, and indeed we are, but….. help yourself to gain the help you need! Rant over, except a please or thank you wouldn’t’ go amiss. Answer - almost certainly yes.

In your postion I would ask first the company what sort of guarantee it offers.

Just another update on the ongoing S-Tronic issues........ Matt, who is a true gentleman member on here and lives not far from me did a full VCDS analysis on the gearbox and read the fault codes, cleared them, read them again multiple times, and then attempted a full Adaption procedure via the VCDS as per manufacturer specifications. There were not really that many fault codes, but the ones specific to the Gearbox were: VCDS 7980: PO726 RPM Signal from ECU - Implausible Signal VCDS 8962: PI707 Clutch 2 Pressure too high VCDS 13791: P2873 Clutch 2 Pressure Engagement too high. That was it really, we cleared the codes, ran the scan again and they didn't return, so then we went onto the full Adaption procedure in VCDS Basic Settings menu, all was well until we got to adaption: IDE02294-Main Pressure valve calibration, whereby it kept giving the message: "Aborted-Safety Reasons" ? We tried this at varying specified gearbox oil Temperature's but to no avail, it just kept aborting half way through the calibration, however when re-reading for any gearbox fault codes multiple times afterwards none appeared ? although we still hadn't / were unable to complete the adaption procedure. I am now going to do a complete oil and filter drain and change service using a Full MEYLE service kit, after this Matt is going to read the codes again with VCDS and try another adaption ! To be continued ........................😮

Hmm, been following this thread with interest, in a previous life I was a naval engineer, so I’m very aware of just how corrosive salt water can be, even over a short time and of course vented discs have an ‘inside’ that you can’t see, that’s corroding away merrily that close to the sea. ceramic discs will stop it all. Coated discs, as Charles said, if it’s just a surface treatment, it clearly won’t survive as a surface very long and will then allow the swept surface of the disc to corrode, but, as it’s the swept area, there’ll still be the nasty grinding noises when you 1st use the brakes. the coating, assuming it covers 100% of the entire disc (inside & out), would still stop those areas corroding but at a much lower cost. depends how much the grinding gets on your nerves. be interesting to see how you get on if you go for the coated discs, I’m fairly close to the coast (7 miles) but it’s not too bad here for salt spray etc, we get some, but only in high winds & storms.

Welcome Isaac, and thanks for joining. Are the working and non working front and rear brakes diagonally opposite? If so, could be associated with ABS-? ‘…help a brother out….’ Masonic? Kind regards, Gareth.

Thanks yes, saw that thread. It seems a common issue with the C7, they like to let water in as much as possible. Further investigation this evening and I narrowed down the leak. See the picture attached, but the leak is coming through a seam in the side wall. Circled the area in red. I have sealed this area with Gorilla waterproof patch & seal tape. I removed the Voltage stabiliser unit to dry it out, and also moved the wiring loom for the Voltage Stabiliser unit up and back out of the spare wheel well up into the area where the main fuse board unit is. I hope that these two actions will cure the problem.

Thank you 😊 lol, well I'm hoping I'll be able to get it back on the road asap as I want to bring my daughter along to the shows. Oh bless ya, hope you get better soon. Definitely, wife and I have been wanting children for the last 7 years.