cliffcoggin

I would think it more likely that the filter was not installed correctly rather than being faulty, but that's not really important. What is important is the possible damage to the engine, which can not be assessed without stripping it. As long as the garage will stand by their new car guarantee you should be covered for any problem that develops in the future. As for the lack of apology, that's discourteous and irritating but words are cheap. Actions are what count.

I suspect that cutting the plastic bumper might reduce the crash resistance of the car even if there is a steel beam behind it. Get some specialist advice before doing anything drastic enough to fail an MOT.

No computer in the car can detect every fault. If you have a knock you need to get it examined because it could be caused by innumerable problems: worn track rod ends, worn CV joints, worn steering joints, worn suspension mounts, loose steering rack, worn wheel bearings. The list is nearly endless.

Faulty or not, the garage that fitted the filter is responsible for rectifying the problem and any associated engine damage. Is the garage disputing that or somehow trying to shift the blame?

Thanks for the clarification.

That's good to know Ross. The attachment of the two lugs to the inside looks messy. The Ebay ad says the item is metal while you say it is plastic. Can you elaborate on the construction?

Well you mentioned bits of plastic in the fluid, though I don't understand where they came from. I guess if some it got into the system it could limit the piston travel, score a seal, jam a valve. In your position I would dismantle both cylinders for thorough cleaning and blow compressed air through the pipe.

Stephen. If the pedal travel was right before you worked on the hydraulics , and if the only change you have made was the master cylinder, then I still believe you have air in the system. On the other hand if the pedal travel was wrong beforehand you could have a worn clutch.

Ten to one you still have air in the system. Since your Eezibleed kit doesn't seem to work properly I suggest you adopt the old-fashioned way of bleeding that requires two people to do the job: one to operate the pedal, the other to operate the bleed screw and top up the reservoir. Briefly the process is: Fill the reservoir. Attach a clear piece of tubing to the bleed nipple with the lower end in a jar. Open the bleed screw about half a turn. Push and hold the pedal down. Close the bleed screw. Lift the pedal. Repeat those steps until no bubbles are seen in the fluid coming out of the slave cylinder. It is essential the reservoir level is not run down to the point that air is drawn in again.

I know nothing of Audi headlight washers but those on my old Granada worked entirely automatically: both the headlights and the wipers had to be on for the washers to operate. Mind you that was 25 years ago, maybe things have regressed since then.

Has it always behaved like this? Have you changed the wiper motor perhaps? The last time I opened a wiper motor (a few decades ago,) the arm travel was fixed by the size of the linkage within.

I have not changed the pads on mine, nevertheless I agree with Gareth. The clips exist for a reason; if they were unnecessary they wouldn't be fitted and pads would be cheaper.

Jess. You need to bleed the air out of the fuel system all the way from the tank to the injectors. Usually the injectors have to be removed and the engine cranked until nothing but fuel comes out of the injectors. It's a messy stinking job which your partner should carry out to ensure he never runs out of fuel again. <G>

Lindsay I am not sure what fault you are describing. Are you saying the key won't enter the barrel, won't turn once entered, or won't operate the switch once entered and turned?

Hello Geoff. (Love the beer name.) I can't be certain, but I would expect sports suspension to have tighter shock absorbers as well as shorter springs so its possible you would have to change both. A change may also affect the steering geometry so you need to be certain of the answers before committing to altering anything.

Chris. Car dealers are not renown for their charity and you are now discovering why the car was so cheap. In my view if the engine is clapped out, then it's likely the rest of the drive train will also be marginal and the car will become a money pit in the years to come. I'd get rid of it as soon as possible.

Please do Martyn, particularly with the source of the unit and your comments on it as I am interested in getting one.

Was the fuel consumption normal before you changed the induction kit? If so, the solution is obvious.

It is possible that non-sensor pads have been fitted as an economy measure.

You mean the seller doesn't know?

Phillip. As Tom said, hot brakes would only be caused if they were binding, and that's easy to diagnose: if one or more wheels feel unusually hot (more than body temperature) after a journey then the brakes are binding. Does the car pull to one side under braking? That's another symptom of a brake binding. I suspect your problem is more likely to be defective master cylinder seals or water contaminated brake fluid.

So tell us what the thing is that is rattling because it doesn't look like a fuel line. How did you cure your problem?

Despite the error message about the aerial, it seems too much of a coincidence that the radio does not work at the same time as a CD is jammed in. Is there no way to forcibly extract the CD with snipe nose pliers for example once the radio is dismantled? Perhaps that would enable the radio to be selected.

That's done the trick Trevor. Many thanks.

I suspect the problem is that the pop up is an intrinsic part of this site, so no matter what extra filters I install in Chrome OS and UbO the thing keeps appearing. I'll keep looking for ways to eradicate it, but if unsuccessful I shall withdraw from the forum.