Leaderboard

Anyone interested in going to this show? Has been great in the past. This year's Jap Vs German with Rogue Static's own twist is back again at our newest venue Aldwinians rugby club in Manchester. bringing the people of Manchester some stunning motors and a great atmosphere all aimed at for the love of cars, don't have a Jap or German motor? not an issue we welcome everyone. We are asking for £5 per car on entry, which will all be donated to our fantastic charity "SSAFA the armed forces charity" who we have proudly supported for years now. there will be trades, food and facilities as per usual with our events, please be aware that the pitch is out of bounds but we are now able to place light vehicles on the apron near the pitch which now gives us more vehicular room than last time. our marshalls and event staff will all have two way radios in case of emergency and all relevant R.A.M.S have been supplied to the venue. So with that all taken care of all you have to do is click going, pop it on your calendar and show up 😁 Traders confirmed: MAS Decals Swan Lady 3D Scratch entertainment (aka DJ Liam) Virtual Rides (VR rollercoaster) Squid Ink Detailing The Coffee Guy And our special guest Dan Red Media we have three Handcrafted awards to give out too: Best Japanese car Best German Car Best in Show This is a static event and we keep to our policy of park up keys out whilst attending our events anyone caught being a !Removed! will be asked to leave and escorted from the venue, better it's us than the venues manager 😉 no tickets just pay in entry our staff will be on hand with donations buckets when you arrive and throughout the day every little can help those in need greatly and we thank you all in advance.

Thanks for being in touch Linds. When you say your small garage tightened the belt, and it now makes a noise - concerns. I’m also intrigued to work out how you actually know the belt is tighter than it was. If (in caps) the belt is tighter than it should be, are you happy to entrust the fitting of a new belt and assembly to them? Water pump? - if cambelt driven on your engine. Wondered what you propose to do about that. Kind regards, Gareth.

Hi everyone fault has been repaired by Abz Audi ,costs covered by Ayr Audi .the problem was caused by faulty abs sensor wiring loom ,great result regards AR

@Steph1234 my dealership is Huntingdon Audi. I am awaiting a response from Ferzana from Audi Executive, she's written to apologise for the delay, no surprise they are inundated with complaints!

Hi they are always a pain as the water from the washer rots everything try a good soak in plusgas then use a deep socket, other than that its a new motor. Steve

Just to say that I bought a space saver 19" wheel from The Wheel Shop along. As Stevey noted above, I then stuck several sections of polystyrene using gaffer tape (pic 1) to support the wheel and keep it off the battery cables to the left and right. Enough space underneath the wheel to store the compressor and tyre repair bottle (pic 2) (just in case). This raised the spare wheel but there was still just enough thread available on the centre to allow me to use the normal large plastic nut to hold the spare in place (pic 3). Although the spare was a little higher than normal due to the polystyrene, there's still enough space to allow the top cover to sit flat in the boot. Lastly the tools including jack fit in the plastic tray (pic 4) between the battery and the back of the rear seats (blue towel round them to stop rattling).

Hi all, I came across an issue recently that appears common enough for people to post with requests for solutions but unusually where I failed to find a concrete fix. So here is my stab at this: The other week I went to do an oil check, pulled the bonnet release level and to my dismay felt no resistance and the bonnet remained firmly shut. Bugger – how to get the bonnet open? There is no access from the front – even destroying off the plastic grill will not get you to any bolts that will help. What is the solution without resorting to a can opener and consequentially a new bonnet?? Here it is… It will be much better to download the attached pdf as this has pics that will help a lot, but instructions with no pics are: 1. Go to B&Q (or equivalent hardware store) and purchase a 4-6mm diameter steel rod between 70 cm and a meter in length. Mine cost £2.60!!! 2. Get a decent vice and make two 90-degree bends at each end of the rod about 10 cm from end of rod by hand (I off-set each end by 90 degrees approx.), to make a ‘emergency bonnet release tool’. 3. Get the front of the car on ramps or jack up as high as possible. Remove undertray and get a good torch and get underneath…. 4. You need to locate the bonnet lock mechanism – it’s at the top of the radiator fans. It will be very hard to see… From below, at the right angle, you should be able to see the underside of the lock mechanism look for the large spring. 5. The reason you are unable to open the bonnet might be: 1, the cable has snapped; or 2, (as in my case) the end of the cable has come lose from the lock mechanism. The 2nd issue is common if you have had the front off and lock carrier into the service position and the cable-end has not been seated back in properly… 5. There are actually 2 sites for a cable to connect. If you have a RHD vehicle then the cable seats into the lower slot; if a LHD then upper slot. You need to get the end of your ‘emergency bonnet release tool’ into one of these two slots, and then twist using the lock housing to lever off and move the release mechanism. If you get into the lower slot the twist right; if you get into the top slot, then twist left. If you use a tube spanner or the end of a ring spanner to get on the other end of the rod where the other 90-degree bend is then you get more force and the bonnet should open! Brilliant. 6. I then decided to add a bit of thick plastic cut to size to cover the cable end housing to stop it coming out again. Drill a small hole and tap a screw into it but do not tighten yet. 7. Reinstall the lock, and reseat the cable end properly, then swing the plastic down over the cable end and tighten screw. Not sure if this will work/last, but at least you now have an ‘emergency bonnet release tool’ to sort it… Hope this is of some help…. Bonnet open solution.pdf

Oh Father in Law!

Hi, as long as the cables for the extra battery don't go inside the wheel tub you should be fine measure the O/D of your existing wheels on your car and marry that against the I/D of the wheel tub, the moulding for the cr@p inflation system is removable and just leaves you the threaded spigot which will anchor your space saver, you can get round the possible noise of the wheel against the floor by buying some cheap stick on insulation, about 4mm thick from eBay and sticking it around the tub, if you mount the wheel face down you can use the space inside the wheel for your jack wrapped in an old towel or similar, just did this on my new Passat cab and found to my joy that the wheel tub was deep enough to take a full size spare. Steve.

Hi Gareth I appreciate your sentiment but realistically I doubt it will make a difference to more than a minority as most of these one post wonders can't even be bothered to look through the legions of post on this wonderful site to see if there is already an answer to their question, NO its far easier just to wait for some poor soul to to spoon feed the answer to them, I find this situation intolerable and on a personal level endorses my opinion that charging a small joining fee would eradicate the free loaders and any funds gathered from serious users would help with the costs of this forum, I have joined a few forums in my time and all required a subscription with the exception of some Ford forums, over the last couple of years the formulae for this situation has become blindingly apparent these people buy these cars in the blind belief that the Audi never goes wrong, someone told them that and its what they wanted to hear, most of the members on here all know that statement to be far from the truth, thats why they are here and after their own problems are solved actively engage in trying to help others, I have noticed lately that a couple of new members have posted the problem and the solution to that problem that they have worked out for themselves, we could definitely do with more members with that mind set. Steve.

Post and run! Joined April 3rd - posted plea for help on April 3rd - not returned since to review any responses. Time taken to construct replies is free of charge, but it is time consuming! Best we can hope for is the information maybe of help to others.

Unless the power steering emis whining etc id say it's normal compared to new cars.

Running it with barely any oil will more than likely knackered it. Have you checked for leaks? As it shouldn't be low unless there's a leak.

Hi here's a little pic of my baby

Hi I hope you bought the three seals as well, radial shaft seal that goes in the slave cylinder, the driveshaft seal for the diff side, you have to take the diff cover off to get at it, then we have the crankshaft seal behind the flywheel and ring gear if thats leaking thats a whole new level, no point in dodging it as it just gets worse and coats the friction plate in engine oil, bit of advice put a bit of plastic over the brake fluid reservoir before !Removed! the lid back on and wrap the end of the pipe in clingfilm when you remove it from the slave cylinder, finally you have to put a bungee on the clutch pedal to stop it falling on the floor, this also stops fluid loss via the master cylinder which iff allowed to travel to the end of the cylinder body will ruin the piston seal so you will need a new one of those as well, I hope you have a four poster to use as the gearbox weighs a ton it took three of us to lift it off of the gearbox jack. Steve.

I've had a look on the forum but I've not yet had the chance to look at the fuel cap recess! I will, soon and get back to you.

Hey everyone! A couple of months ago I picked up my first ever Audi, after owning Hondas for the past 20 years! Went for a 2017 S3 in Nano grey and absolutely love it!! Came with a great spec, and just fitted some RacingLine springs, and a set of 19” APR wheels! Very happy to be part of team Audi!! 😃

How old is the battery? If the battery is starting to fail it can throw up various electrical issues.

Too true, what would be worse is an eco boost with a powershift auto gearbox!

PS; it’s not really safe to drive at all TBH with collapsed suspension on 1 side, and defo not at any speed over 30. My Allroad had the tyre rubbing on the wheel arch when it blew a bag. sorry!

Hi its the sealing ring, most likely they did not change it with the unit problem being that you have to buy the seal separately and they are quite expensive, its either the seal or they have damaged the locking ring that holds the pump in when they re tightened it, the third hole looks like a breather, easiest way to check is get a small length of wire and push it into the hole and see if it bottoms out, if it does its the seal. Steve.

Further update on the 7 Speed S-Tronic DL-501 issue ...... I haven't been able to get the adaption re-done yet after the full gearbox and both filters service as Matt with VCDS has been incredibly busy with his day job, but the one thing I will say after using the car for a few weeks now is it is incredibly smoother than it was before the service and the first VCDS mild adaption, no longer does it thump from second to first and even in reverse there seems to be a definite difference in the take up of the gear, especially on a slope, something it didn't like doing at all before the service, I am genuinely surprised how fresh filters and proper manufacturer recommended "MEYLE" DSG OIL can make that much of a difference, I haven't taken it on a long run yet and got everything in the gearbox up to a constant temperature and speed but around town driving is noticeably much smoother. As it started to fail on me and throw the dreaded yellow warning light on the dash after long motorway cruising I don't want to count my chickens too soon, but I'm hopeful that with a final and Full VCDS Gears Adaption my problem may well be pretty much sorted, as usual will keep posting updates for other members ......... 🤔

Hi I would definitely get some body in that line of work to look at it and tell you realtime what's been done, never been a fan of mapping as half the clowns out there have no idea what they are doing or what the long term implications of their work is, are you still getting codes? Steve.

Yes I had a lot of trouble trying to get the service history off them. They kept saying they couldn’t get hold of it as they were not the registered keeper Will follow your advice for future purchases. Thanks again.

Hi Natasha and welcome, this forum has a lot of info on Q7 ownership and its pitfalls as well as solutions to those pitfalls. Steve.

Bill. The Audi service schedule is more or less all you need do to keep it in decent condition, though I would add two caveats: 1/ Change the cambelt ahead of schedule if it has not been replaced for a few years. Even though the car may not have reached the recommended mileage, (you have not mentioned the actual distance covered since the belt was last changed,) belts can degrade even when not used. Given the consequences of belt failure abroad it makes sense to my mind to change it in advance. 2/ Take the car for a fast motorway journey of about half an hour well before your next continental holiday. That will reveal any faults that may need to be sorted out before you go abroad.

Welcome Alberto, Are you saying you and/or your son are capable of safely renewing brake pads? It seems you have already bought replacement pads. Since the seller seems disinterested in sorting it out, why not carry out your own assessment of the remaining brake pad thickness, and simply renew them - since you have them. Worse possible case:- brake pad wear light remains on after you have done that -? Worry about sorting that out when you get to that point. Perhaps you could let us know how you get on. Kind regards, Gareth.

Welcome Fi, and thanks for joining. First things first:- Can we take it you have studied copy of the on-line MOT history for this car? Also, have you seen evidence of its service history? Have you done an on-line DVLA Vehicle Check to see when the last V5 was issued? This will give you some idea of how long the last owner has owned it? Short ownership - possibly not good. Down to specifics:- Water leaks- search the forum for issues and possible solutions. Panoramic roof - potentially a problem area due to generally non solvable leaks. Personal view ( pardon the pun!) I wouldn’t be interested. Hopefully owner members will fill in the remaining answers for you. Hope some of this helps, Kind regards, Gareth.

NICE B5 BUD

Ditto what Gareth wrote. Let me add that it is always wise to change the water pump belt at the same time as the cambelt because the same expensive work is needed to access them both.

Will do me for now.

Hi it took so long because the software to run electric power steering was not that well developed, if mechanical steering fails you can still steer, on the early electrical steering if it fails you are stuck, the main reason for the development of electric steering was emissions as it wont require the engine to drive the pump thus pushing up engine emissions and electric steering has been about on production cars since about 2008. Steve.

For sale: 2003 Audi A3 Quattro Sport 1.9 TDI (130 BHP) 3 door hatchback The car has fairly low mileage for its age (not quite146,000 miles). Careful lady owner from 2007 to present (1 prior owner) Purchased in 2007 the car is still running well and has been serviced at makers specified intervals. (Full service history available). MOT covers up to 11 November 2024. Latest regular cambelt & water pump replacement was January 2021 (@135,800 miles). Reconditioned gearbox & new clutch in January 2022 (@139,900 miles). All road springs have been renewed. Suspension bushes renewed. New headlamp housings were fitted in 2017. New battery was fitted in February 2023 (5 year guarantee). New front tyres in November 2023. (Rear tyres have over 60% tread remaining). Minor mechanical repairs were addressed as required during ownership, & details can be provided. There are a few very minor bodywork ‘dings’. Alarm removed for repair (available). Fuel & temp gauges under reading. Love this car but reluctantly selling as we don’t have space for it any more. Looking for best offer of £1,000 plus for this rare A3 variant.

I have a fix. I also own a mk2 Golf and I spotted a detail on the gas peddle cable that is the same for adjustment, at the end there is a castellated section with a clip on it for tension, I added a couple of castellations to the tension and I now have 1k solid tickover. 😁 The clip sinks into the rubber grommet, lowering the tension over time. 😎

Heres how I did mine on my previous car. The sensor was just over a tenner on eBay. You’ll need to scroll about halfway down the page when it opens. https://www.detailingworld.co.uk/threads/project-audi.348112/page-9

I'd recommend a diagnostic check to see if any fault codes flag up. If you've bought it from a dealer then they have to fix it foc in the first 30 days from sale as you're still entitled to a full refund within that time.

Software version is 3620 MMI software version is release-35.12-2126-SNAPSHOT-28.06.2021-13:58:42 Navigation database is V03959822FK_P1140_EU_2024.03 Since having it updated I now have Android Auto wirelessly which I didn't before (had to connect a cable) Hope this helps !

Hi have you tried eBay with that part number they have loads of them.

On the AdBlue topic, you can get the no restart message flashed out of the ECU at a fraction of the cost of replacement parts. Give Andy at https://ecuflash.co a call. On the wider get rid or keep topic, I’ll never buy another Audi again. 16 plate B9 (actually B8.5 according to it’s car plate). Owned for 5ish years and I’ve put 50k on it. 80k in total. I’ve spent about 7k keeping it on the road, fixing issues that shouldn’t be there for a car this age and mileage. Not including “on-the-road costs” like tyres. -Had the brake servo/abs issue. -Had the AdBlue issue. -Odometer failed and had to be replaced. -2 broken rear coil springs. -Have the issue with low interior heat. -5 (yes five) new sets of front discs/pads due to excessive warping. -1 new calliper. I can go on, but suffice to say my experience of “Vorsprung durch Technik” is actually “our technology is crap”.

Here's my (now Sold) 2005 A3 2.0 TDI sport.. Replaced by 2012 A3 1.4tfsi ... work in progress...

Anybody know where I can get my gearbox mechatronics unit checked as I have lost my reverse gear and have a warning sign audi talking thousands of van need a quick fix west Midlands area anybody body know a good mechanic for the job

Well well well After spending a small fortune this last 18 months on my B8 I stumbled on a stunning A4, B9 Avant 2017 in twilight grey at a price I just couldn’t miss - pic below…. PS A4 B8 in cuvee silver now looking for a new home

Thank you 😊 lol, well I'm hoping I'll be able to get it back on the road asap as I want to bring my daughter along to the shows. Oh bless ya, hope you get better soon. Definitely, wife and I have been wanting children for the last 7 years.

Hi can anyone help my car is throwing on the EML with the code for running lean on bank 1. Also it sometimes has a slight misfire. Do you how I can fix it?

Hi all, I have an update... Lol Loud scraping noise = destroyed Balance Shaft Chain & Crank Cog Teeth. Remedy = New Timing Chain & Crank Cog. I did the work myself, which took an age of learning and an age of fixing, but it's all good now. 😁 Thanks, Paul.