Leaderboard

Anyone interested in going to this show? Has been great in the past. This year's Jap Vs German with Rogue Static's own twist is back again at our newest venue Aldwinians rugby club in Manchester. bringing the people of Manchester some stunning motors and a great atmosphere all aimed at for the love of cars, don't have a Jap or German motor? not an issue we welcome everyone. We are asking for £5 per car on entry, which will all be donated to our fantastic charity "SSAFA the armed forces charity" who we have proudly supported for years now. there will be trades, food and facilities as per usual with our events, please be aware that the pitch is out of bounds but we are now able to place light vehicles on the apron near the pitch which now gives us more vehicular room than last time. our marshalls and event staff will all have two way radios in case of emergency and all relevant R.A.M.S have been supplied to the venue. So with that all taken care of all you have to do is click going, pop it on your calendar and show up 😁 Traders confirmed: MAS Decals Swan Lady 3D Scratch entertainment (aka DJ Liam) Virtual Rides (VR rollercoaster) Squid Ink Detailing The Coffee Guy And our special guest Dan Red Media we have three Handcrafted awards to give out too: Best Japanese car Best German Car Best in Show This is a static event and we keep to our policy of park up keys out whilst attending our events anyone caught being a !Removed! will be asked to leave and escorted from the venue, better it's us than the venues manager 😉 no tickets just pay in entry our staff will be on hand with donations buckets when you arrive and throughout the day every little can help those in need greatly and we thank you all in advance.

Thanks for being in touch Linds. When you say your small garage tightened the belt, and it now makes a noise - concerns. I’m also intrigued to work out how you actually know the belt is tighter than it was. If (in caps) the belt is tighter than it should be, are you happy to entrust the fitting of a new belt and assembly to them? Water pump? - if cambelt driven on your engine. Wondered what you propose to do about that. Kind regards, Gareth.

@Steph1234 my dealership is Huntingdon Audi. I am awaiting a response from Ferzana from Audi Executive, she's written to apologise for the delay, no surprise they are inundated with complaints!

Hi they are always a pain as the water from the washer rots everything try a good soak in plusgas then use a deep socket, other than that its a new motor. Steve

Just to say that I bought a space saver 19" wheel from The Wheel Shop along. As Stevey noted above, I then stuck several sections of polystyrene using gaffer tape (pic 1) to support the wheel and keep it off the battery cables to the left and right. Enough space underneath the wheel to store the compressor and tyre repair bottle (pic 2) (just in case). This raised the spare wheel but there was still just enough thread available on the centre to allow me to use the normal large plastic nut to hold the spare in place (pic 3). Although the spare was a little higher than normal due to the polystyrene, there's still enough space to allow the top cover to sit flat in the boot. Lastly the tools including jack fit in the plastic tray (pic 4) between the battery and the back of the rear seats (blue towel round them to stop rattling).

Hi all, I came across an issue recently that appears common enough for people to post with requests for solutions but unusually where I failed to find a concrete fix. So here is my stab at this: The other week I went to do an oil check, pulled the bonnet release level and to my dismay felt no resistance and the bonnet remained firmly shut. Bugger – how to get the bonnet open? There is no access from the front – even destroying off the plastic grill will not get you to any bolts that will help. What is the solution without resorting to a can opener and consequentially a new bonnet?? Here it is… It will be much better to download the attached pdf as this has pics that will help a lot, but instructions with no pics are: 1. Go to B&Q (or equivalent hardware store) and purchase a 4-6mm diameter steel rod between 70 cm and a meter in length. Mine cost £2.60!!! 2. Get a decent vice and make two 90-degree bends at each end of the rod about 10 cm from end of rod by hand (I off-set each end by 90 degrees approx.), to make a ‘emergency bonnet release tool’. 3. Get the front of the car on ramps or jack up as high as possible. Remove undertray and get a good torch and get underneath…. 4. You need to locate the bonnet lock mechanism – it’s at the top of the radiator fans. It will be very hard to see… From below, at the right angle, you should be able to see the underside of the lock mechanism look for the large spring. 5. The reason you are unable to open the bonnet might be: 1, the cable has snapped; or 2, (as in my case) the end of the cable has come lose from the lock mechanism. The 2nd issue is common if you have had the front off and lock carrier into the service position and the cable-end has not been seated back in properly… 5. There are actually 2 sites for a cable to connect. If you have a RHD vehicle then the cable seats into the lower slot; if a LHD then upper slot. You need to get the end of your ‘emergency bonnet release tool’ into one of these two slots, and then twist using the lock housing to lever off and move the release mechanism. If you get into the lower slot the twist right; if you get into the top slot, then twist left. If you use a tube spanner or the end of a ring spanner to get on the other end of the rod where the other 90-degree bend is then you get more force and the bonnet should open! Brilliant. 6. I then decided to add a bit of thick plastic cut to size to cover the cable end housing to stop it coming out again. Drill a small hole and tap a screw into it but do not tighten yet. 7. Reinstall the lock, and reseat the cable end properly, then swing the plastic down over the cable end and tighten screw. Not sure if this will work/last, but at least you now have an ‘emergency bonnet release tool’ to sort it… Hope this is of some help…. Bonnet open solution.pdf

Oh Father in Law!

Hi, as long as the cables for the extra battery don't go inside the wheel tub you should be fine measure the O/D of your existing wheels on your car and marry that against the I/D of the wheel tub, the moulding for the cr@p inflation system is removable and just leaves you the threaded spigot which will anchor your space saver, you can get round the possible noise of the wheel against the floor by buying some cheap stick on insulation, about 4mm thick from eBay and sticking it around the tub, if you mount the wheel face down you can use the space inside the wheel for your jack wrapped in an old towel or similar, just did this on my new Passat cab and found to my joy that the wheel tub was deep enough to take a full size spare. Steve.

Hi Gareth I appreciate your sentiment but realistically I doubt it will make a difference to more than a minority as most of these one post wonders can't even be bothered to look through the legions of post on this wonderful site to see if there is already an answer to their question, NO its far easier just to wait for some poor soul to to spoon feed the answer to them, I find this situation intolerable and on a personal level endorses my opinion that charging a small joining fee would eradicate the free loaders and any funds gathered from serious users would help with the costs of this forum, I have joined a few forums in my time and all required a subscription with the exception of some Ford forums, over the last couple of years the formulae for this situation has become blindingly apparent these people buy these cars in the blind belief that the Audi never goes wrong, someone told them that and its what they wanted to hear, most of the members on here all know that statement to be far from the truth, thats why they are here and after their own problems are solved actively engage in trying to help others, I have noticed lately that a couple of new members have posted the problem and the solution to that problem that they have worked out for themselves, we could definitely do with more members with that mind set. Steve.

Post and run! Joined April 3rd - posted plea for help on April 3rd - not returned since to review any responses. Time taken to construct replies is free of charge, but it is time consuming! Best we can hope for is the information maybe of help to others.

Unless the power steering emis whining etc id say it's normal compared to new cars.

Kat. Who or what is telling you that the ABS module is faulty? The dashboard lamp, a proper VAGCOM diagnosis, a cheap code reader, a mechanic, or something else?

Is it worth considering the abs sensors? As they're cheaper to replace before changing the module

Hi everyone fault has been repaired by Abz Audi ,costs covered by Ayr Audi .the problem was caused by faulty abs sensor wiring loom ,great result regards AR

No I actually just went to my local mechanic. I'm not sure if I just got lucky but he's very trustworthy and reasonably priced. Based around Dalston in East London.

I had a garage do it as it’s not easy on a drive! But forum discussions at the time (if you do the job yourself) suggested blanking off the air pipe and running the pump to check for leaks (dont run it for more than 1 minute in ten) it’s just not designed for it and will likely burn the motor or compressor seals. if you can pressurise it another way to test, I’d do so.

PS; it’s not really safe to drive at all TBH with collapsed suspension on 1 side, and defo not at any speed over 30. My Allroad had the tyre rubbing on the wheel arch when it blew a bag. sorry!

I'd suspect that the bag isn't inflating and changing it is the only option.

those error messages are in fact a frequent thing and it comes down to the sensitivity of your settings (radar, collision assist etc). You can adjust your settings to pick up far less in the realms or items vs distance but not recommended. FYI the car records loss of vision or detection as faults and stay logged until removed. I recently had Audi assist come out for something else related I had 136 codes stored and following that CAM bus errors because of how many were stored. I was politely reminded that these issues have become a common issue causing modules to slow down or self fault due to bus memory being clogged with error codes. from time to time it’s recommended to review and clear. Ideally around service intervals. You’d think your main dealer would do this as part of their service but they don’t and leave them…

I put it down to the camera maybe picking up something that it couldn’t decifer, or maybe dust / dirt obstructing it. It’s never caused any issues. I think this has been brought up on here previously with no real conclusion.

Finally this issue has been explained in a simple manner. I've been chasing a leak in my GTI with the same engine and haven't found anyone explain it the way you did. Thanks for this and I did subscribe and like this! Thanks man, take care Kodi

A(nonymous). Given that this thread is over seven years old it is unlikely you will get a response from the originator. Nevertheless there are some useful suggestions in it. Have you tried any of them?

Sounds like a longer term good move Fi. Could I reinforce the procedure I go through before viewing:- Check the on-line MOT history. Check the DVLA vehicle check to see when the latest V5 was issued. Can give you some idea of last change of owner. Ask the seller to e-mail copy of the Audi on-line service history and/or any servicing receipts. If you have opposition in any respect - start twitching! At the same time as requesting this off the seller, ask your local dealer if they would outline ( and ideally provide copy) the service record they have on the Audi system. All this can be done from the comfort of your arm chair, and will form the backbone of sound research before you decide to view. Good luck with your quest, and please let us know how you get on. Kind regards, Gareth.

Well after lots of research and worry, I decided against the purchase of that particular car! I noticed a couple of electrical warnings, and with the wet boot, I think it may have been an ongoing problem. So just waiting for my deposit back. Finding it very difficult to find a good used Q7! Thank you for your help and advice though.

Glad you got sorted 🙂

Hi Magnet, Thanks for commenting. I had to drive my car today 70 miles the noise was not apparent ongoing but just when turning on the engine and going slower. I know the belt is tighter because pre garage visit- I took off the casing to see the cam belt - I wiggled it and it was more loose. On hearing the change in sound - rechecked under the casing and the cam belt is definitely tighter. I asked the garage after changing the bolts if my cam belt was OK and they did not say they had done anything to it. The independent garage specialise in audi and use genuine parts. They seem to have a good rep. The water pump is on the opposite side on my 1.4 petrol engine I am told. I am thinking of going back tomorrow to ask them about it. (Noise).

Well i finally got my coolant leak issue resolved. Hose and seal issues. So extended warranty wouldn't cover it. Dealer said they will cover costs as gesture of good faith. ( i did wait a while for an appointment) I am pleasantly surprised, and faith in the dealers has been considerably restored. Any other pleasant dealership stories out there.

Welcome to the forum you'll find the members on here are a friendly and helpful bunch 🙂 Those v70s were great!

Hi Andy unfortunately not, Audi have all the codes for every model from 2011 up and wont supply that information to any outside key suppliers, its not like the old days when you got a dummy key and just coded the new transducer in that key via the ignition. Steve.

Audi have replaced the drivers door latch under warranty part no. A4K2 837 016 H the car still at Audi checking hand brake .

Getting my lock system replaced at the local Audi garage on my A6 2021 .. had the same problem

Hi , 2017 a6 with the same leak on both sides of the car , running down A frame and into foot well . The water as I'm sure is the same for most gets in where the water flow / level becomes to much for the drain and builds up ( doesn't take much ) it overflows to the inside of the wind defector and the leak gets in where there is a steel spring finger . Water gets in where it locates towards the front .... BUT regardless of that , iv found at the rear of the spring finger , under hole is a 10mm × 10mm square hole in the frame on both sides which flows directly in onto the headliner. Joke of a design. I'm working on a fix at the minute 🤞

Hello Jay, The definitive answer lies in the build record, and you should be able to obtain this from Audi Cust. services, or possibly through a dealer - both through the VIN. Possible theory:- delayed release due to the chip crisis?? Kind regards, Gareth.

remapping with adblue delete should help,

For sale: 2003 Audi A3 Quattro Sport 1.9 TDI (130 BHP) 3 door hatchback The car has fairly low mileage for its age (not quite146,000 miles). Careful lady owner from 2007 to present (1 prior owner) Purchased in 2007 the car is still running well and has been serviced at makers specified intervals. (Full service history available). MOT covers up to 11 November 2024. Latest regular cambelt & water pump replacement was January 2021 (@135,800 miles). Reconditioned gearbox & new clutch in January 2022 (@139,900 miles). All road springs have been renewed. Suspension bushes renewed. New headlamp housings were fitted in 2017. New battery was fitted in February 2023 (5 year guarantee). New front tyres in November 2023. (Rear tyres have over 60% tread remaining). Minor mechanical repairs were addressed as required during ownership, & details can be provided. There are a few very minor bodywork ‘dings’. Alarm removed for repair (available). Fuel & temp gauges under reading. Love this car but reluctantly selling as we don’t have space for it any more. Looking for best offer of £1,000 plus for this rare A3 variant.

I have a fix. I also own a mk2 Golf and I spotted a detail on the gas peddle cable that is the same for adjustment, at the end there is a castellated section with a clip on it for tension, I added a couple of castellations to the tension and I now have 1k solid tickover. 😁 The clip sinks into the rubber grommet, lowering the tension over time. 😎

Well Steve, someone said I could be like a good wine, and will improve with age - I don’t believe it - but I am still blessing every day where I’m still able to do what I want to do. Some things are impossible, despite what my mind tells me! Take care and kind regards, Gareth.

Yes history looks all ok just looking for a car that looks the part, goes, peanuts on tax and way less fuel cost compared to my 3.0L Discovery 4.

Will do, looking forward to getting it back but I feel my ownership may not last long at this point as garage has advised me to get fixed and get gone, but that would mean I’d lose a fair bit in the short time I’ve had it, and I’d just put 4 new tires on.

Hello R? Certainly +1 for Steve’s recommendation. Why is everyone still hell bent on using ECP despite having virtually discontinued -? their high % discounts on their ‘Retail price’, which generally ended up with the buyer paying more than they would have paid elsewhere? Another tip - but keep it to yourself!! - PinM often have a % discounts at the end of the month. I too have had superb service from them, and they are always my first port of call for any parts I need. Incase it helps, a family member is now ‘experimenting’ with Brembo following disappointment with genuine JLR parts - so far, Brembo are proving to be more efficient and longer lasting. Let us know how you get on. Kind regards, Gareth. p.s. Why not fill in your name R, and your location - big place is England! We don’t bite on here, we just hope to come over as being helpful.

Yea an Audi independent is an option or an auto electrican

Hi Dan. I would think paint would last that long being bombarded by grit off the road. But, you can buy a proper black surround and grill for the A3 from E Bay for £120. Tony

Thank you 😊 lol, well I'm hoping I'll be able to get it back on the road asap as I want to bring my daughter along to the shows. Oh bless ya, hope you get better soon. Definitely, wife and I have been wanting children for the last 7 years.

Thank you so much. Will look into them. Sorry to hear you've been ill. Hope you're recovering now? I'd suspended work on the A6 in the short term whilst I've been doing the house up and getting prepped for our new (first) arrival.

Hello Thomas, I guess you have a conventional manual handbrake, by the year of the car. Assuming the pads and calipers are in a serviceable condition, then it maybe wise to totally slacken handbrake adjustment to a point where the cables can be disconnected at both wheels. You can then sharply apply the footbrake and ensure both rear wheels lock up properly and then fully release properly. It would be great if your friendly MOT station could retest the rear brake efficiency and balance to ensure they are working properly - oops, just realised Ireland - so Government testing?? Once you have established correctly working rear wheel braking , you can then tackle the handbrake cable efficiency. Do both cables pull and release properly? Renew if any doubt. Your A4 may have the same set up as the similar year A3, whereby the cables pass through aluminium guide tubes, and they can stick within these tubes. New tubes will be necessary and I think these are main dealer parts only. Liberal application of WD40 may assist handbrake cable action and removal of tubes if necessary. Kind regards, Gareth.