Leaderboard

Thanks for being in touch Linds. When you say your small garage tightened the belt, and it now makes a noise - concerns. I’m also intrigued to work out how you actually know the belt is tighter than it was. If (in caps) the belt is tighter than it should be, are you happy to entrust the fitting of a new belt and assembly to them? Water pump? - if cambelt driven on your engine. Wondered what you propose to do about that. Kind regards, Gareth.

Hi they are always a pain as the water from the washer rots everything try a good soak in plusgas then use a deep socket, other than that its a new motor. Steve

Just to say that I bought a space saver 19" wheel from The Wheel Shop along. As Stevey noted above, I then stuck several sections of polystyrene using gaffer tape (pic 1) to support the wheel and keep it off the battery cables to the left and right. Enough space underneath the wheel to store the compressor and tyre repair bottle (pic 2) (just in case). This raised the spare wheel but there was still just enough thread available on the centre to allow me to use the normal large plastic nut to hold the spare in place (pic 3). Although the spare was a little higher than normal due to the polystyrene, there's still enough space to allow the top cover to sit flat in the boot. Lastly the tools including jack fit in the plastic tray (pic 4) between the battery and the back of the rear seats (blue towel round them to stop rattling).

Hi all, I came across an issue recently that appears common enough for people to post with requests for solutions but unusually where I failed to find a concrete fix. So here is my stab at this: The other week I went to do an oil check, pulled the bonnet release level and to my dismay felt no resistance and the bonnet remained firmly shut. Bugger – how to get the bonnet open? There is no access from the front – even destroying off the plastic grill will not get you to any bolts that will help. What is the solution without resorting to a can opener and consequentially a new bonnet?? Here it is… It will be much better to download the attached pdf as this has pics that will help a lot, but instructions with no pics are: 1. Go to B&Q (or equivalent hardware store) and purchase a 4-6mm diameter steel rod between 70 cm and a meter in length. Mine cost £2.60!!! 2. Get a decent vice and make two 90-degree bends at each end of the rod about 10 cm from end of rod by hand (I off-set each end by 90 degrees approx.), to make a ‘emergency bonnet release tool’. 3. Get the front of the car on ramps or jack up as high as possible. Remove undertray and get a good torch and get underneath…. 4. You need to locate the bonnet lock mechanism – it’s at the top of the radiator fans. It will be very hard to see… From below, at the right angle, you should be able to see the underside of the lock mechanism look for the large spring. 5. The reason you are unable to open the bonnet might be: 1, the cable has snapped; or 2, (as in my case) the end of the cable has come lose from the lock mechanism. The 2nd issue is common if you have had the front off and lock carrier into the service position and the cable-end has not been seated back in properly… 5. There are actually 2 sites for a cable to connect. If you have a RHD vehicle then the cable seats into the lower slot; if a LHD then upper slot. You need to get the end of your ‘emergency bonnet release tool’ into one of these two slots, and then twist using the lock housing to lever off and move the release mechanism. If you get into the lower slot the twist right; if you get into the top slot, then twist left. If you use a tube spanner or the end of a ring spanner to get on the other end of the rod where the other 90-degree bend is then you get more force and the bonnet should open! Brilliant. 6. I then decided to add a bit of thick plastic cut to size to cover the cable end housing to stop it coming out again. Drill a small hole and tap a screw into it but do not tighten yet. 7. Reinstall the lock, and reseat the cable end properly, then swing the plastic down over the cable end and tighten screw. Not sure if this will work/last, but at least you now have an ‘emergency bonnet release tool’ to sort it… Hope this is of some help…. Bonnet open solution.pdf

Oh Father in Law!

Hi, as long as the cables for the extra battery don't go inside the wheel tub you should be fine measure the O/D of your existing wheels on your car and marry that against the I/D of the wheel tub, the moulding for the cr@p inflation system is removable and just leaves you the threaded spigot which will anchor your space saver, you can get round the possible noise of the wheel against the floor by buying some cheap stick on insulation, about 4mm thick from eBay and sticking it around the tub, if you mount the wheel face down you can use the space inside the wheel for your jack wrapped in an old towel or similar, just did this on my new Passat cab and found to my joy that the wheel tub was deep enough to take a full size spare. Steve.

Hi Gareth I appreciate your sentiment but realistically I doubt it will make a difference to more than a minority as most of these one post wonders can't even be bothered to look through the legions of post on this wonderful site to see if there is already an answer to their question, NO its far easier just to wait for some poor soul to to spoon feed the answer to them, I find this situation intolerable and on a personal level endorses my opinion that charging a small joining fee would eradicate the free loaders and any funds gathered from serious users would help with the costs of this forum, I have joined a few forums in my time and all required a subscription with the exception of some Ford forums, over the last couple of years the formulae for this situation has become blindingly apparent these people buy these cars in the blind belief that the Audi never goes wrong, someone told them that and its what they wanted to hear, most of the members on here all know that statement to be far from the truth, thats why they are here and after their own problems are solved actively engage in trying to help others, I have noticed lately that a couple of new members have posted the problem and the solution to that problem that they have worked out for themselves, we could definitely do with more members with that mind set. Steve.

Post and run! Joined April 3rd - posted plea for help on April 3rd - not returned since to review any responses. Time taken to construct replies is free of charge, but it is time consuming! Best we can hope for is the information maybe of help to others.

Unless the power steering emis whining etc id say it's normal compared to new cars.

Kat. Who or what is telling you that the ABS module is faulty? The dashboard lamp, a proper VAGCOM diagnosis, a cheap code reader, a mechanic, or something else?

Is it worth considering the abs sensors? As they're cheaper to replace before changing the module

https://www.google.com/search?q=audi+a6+gearbox+code+QLX.&oq=audi+a6+++gearbox+code+QLX.&gs_lcrp=EgZjaHJvbWUyBggAEEUYOTIGCAEQRRg80gEJMTA3MGowajE1qAIAsAIA&sourceid=chrome&ie=UTF-8

Hello I wanted to add that I just added some oil because maybe enough oil had leaked to the point of metal to metal grind would start to occur. The sound stopped and I’ll be getting a oil change this weekend I’ll be back to report 🫡

No I actually just went to my local mechanic. I'm not sure if I just got lucky but he's very trustworthy and reasonably priced. Based around Dalston in East London.

Got this sorted. Had to get rack refurbished. Company said that ecu on rack read and faults were water damage and voltage inconsistency. Found broken wire on loom travelling over back differential. Got this replaced and rack fitted and after 8 weeks we are out and about again 🤦🏼

I had a garage do it as it’s not easy on a drive! But forum discussions at the time (if you do the job yourself) suggested blanking off the air pipe and running the pump to check for leaks (dont run it for more than 1 minute in ten) it’s just not designed for it and will likely burn the motor or compressor seals. if you can pressurise it another way to test, I’d do so.

My settings are already on the least sensitive. Still happens. Doesn’t real worry me though. I’m keeping it into its fourth year now as I quite like it and nothing within a reasonable price that is compatible came up. I’ve got exactly 12 months to plan what’s next…

those error messages are in fact a frequent thing and it comes down to the sensitivity of your settings (radar, collision assist etc). You can adjust your settings to pick up far less in the realms or items vs distance but not recommended. FYI the car records loss of vision or detection as faults and stay logged until removed. I recently had Audi assist come out for something else related I had 136 codes stored and following that CAM bus errors because of how many were stored. I was politely reminded that these issues have become a common issue causing modules to slow down or self fault due to bus memory being clogged with error codes. from time to time it’s recommended to review and clear. Ideally around service intervals. You’d think your main dealer would do this as part of their service but they don’t and leave them…

Hello Mick, Thanks for joining, but without being dismissive, you really should entrust this issue to your supplying dealer. You will have/will be paying a lot of funds for this new vehicle, and you really should not be expected to trouble-shoot issues with it. Have you contacted them? Kind regards, Gareth.

Thanks for the links Kev. Annoyingly last week I discovered from my mechanic that if I buy any 2.5tdi engine and keep my current injection pump and ECU the car will think the replacement engine is the original and will run. Wish I'd known that a year ago instead of worrying about coding of injection pumps and imobilisers etc. So my simplest option is to find a bau version of the 2.5tdi as this was the last variation of that engine and most refined in theory. Trying to find one with low miles and proven service history, but naturally this is proving difficult.

Hi Sorry it’s been a while since I logged in. They eventually found a very small oil leak from a seal on the drive shaft that was spitting oil onto the turbo. They had to remove the engine to fix it. ive since got rid of the A6 and am driving an A3 instead. I’m just pretty sure Audi make great smaller cars but the quality control in the big ones is just not good enough. declan

Turns out the Haynes book threw me a red herring on the ACE engine the mid shaft only runs the oil pump, therefore no need to have a timing point on the cog. I found this out after rotating it with my hot wire rig setup but nothing was happening and the wires to the coil from my golf were getting hot. I even took off the distributor cap and sure enough the arm was not moving. Even I found another string on the net that has a sketch of a hole by the bell housing that should show a timing mark, however that was not moving. Then I went back to Haynes and looked up distributor where I found, I quote “ACE and AAR engines, the distributor is located on the right hand of the engine and is driven off the rear of the camshaft. After finding out my cam belt was 2 teeth out, I put all back together again, indecently the distributor cap had a mount bolt loose, that would not help. I manually cranked the engine over, no issues. Started on the button idled fine up to 60 degrees where the engine started to search again, but not as bad as before. I just instinctively unplugged the isv and she purred like a cat at just over 1k and was rock solid, plugged isv back in and the searching came back, new one on order. I turned off the car, and waited 5 minutes but she would not fire up. Back to Haynes for inspiration and eventually I found a problem that I feel is the root cause,…. The connector on the loom to Part OEM 034919369C has been wired wrongly, not only that somebody tried to correct the fault by forcing the two parts upside down and the new connector is also broken. I have found a you tube person who prints new ones as the connector is no longer available. 3-pin connector 893971974. Has anyone got a wiring diagram for the correct wires to locations they could show to me so I can get this faux pas sorted out. I feel close to getting this car running the way she should again, what an interesting day I have had.

A(nonymous). Given that this thread is over seven years old it is unlikely you will get a response from the originator. Nevertheless there are some useful suggestions in it. Have you tried any of them?

Did you find out how to remove the center console in the end?

Well after lots of research and worry, I decided against the purchase of that particular car! I noticed a couple of electrical warnings, and with the wet boot, I think it may have been an ongoing problem. So just waiting for my deposit back. Finding it very difficult to find a good used Q7! Thank you for your help and advice though.

Welcome to the forum you'll find the members on here are a friendly and helpful bunch 🙂 air suspension problems are well documented and can be costly to repair

Bill. The Audi service schedule is more or less all you need do to keep it in decent condition, though I would add two caveats: 1/ Change the cambelt ahead of schedule if it has not been replaced for a few years. Even though the car may not have reached the recommended mileage, (you have not mentioned the actual distance covered since the belt was last changed,) belts can degrade even when not used. Given the consequences of belt failure abroad it makes sense to my mind to change it in advance. 2/ Take the car for a fast motorway journey of about half an hour well before your next continental holiday. That will reveal any faults that may need to be sorted out before you go abroad.

I solved the vibration of the airbag at low revs by lining the space under the airbags with this packing foam. It's quiet for now. 🙂

Welcome to the forum you'll find the members on here are a friendly and helpful bunch 🙂 Those v70s were great!

Hi Andy unfortunately not, Audi have all the codes for every model from 2011 up and wont supply that information to any outside key suppliers, its not like the old days when you got a dummy key and just coded the new transducer in that key via the ignition. Steve.

Hi lot of common sense on that statement, that’s what I was planning to do myself ,Audi dealership what a letdown 1 st time buying from them my 1 Audi was back in 80 s Audi 80 cd thanks for thoughts regards AR

Had the same problem, Audi replaced lock system, A4K2 837 016 H …. Audi part

Getting my lock system replaced at the local Audi garage on my A6 2021 .. had the same problem

Hi everyone I'm new here and already had some great help from members, read loads of useful stuff, I've personally imported a 8p s3 in yellow for my wife from Japan it's not our first import I buy all our cars from Japan. I will try to add a couple of photos soon

Ditto what Gareth wrote. Let me add that it is always wise to change the water pump belt at the same time as the cambelt because the same expensive work is needed to access them both.

remapping with adblue delete should help,

New here, never owned an Audi until now heres a wee pic

Software version is 3620 MMI software version is release-35.12-2126-SNAPSHOT-28.06.2021-13:58:42 Navigation database is V03959822FK_P1140_EU_2024.03 Since having it updated I now have Android Auto wirelessly which I didn't before (had to connect a cable) Hope this helps !

Problem resolved. I replace the tailgate lock. My conclusion is that the lock did not "signal" door open and this causes the towbar to not release etc....

Lovely to meet everyone. Recently purchased an RS4 Carbon Black Avant (2020). Certainly more interesting than my wife's 1.2T Fiesta.. 👋

Hi Dan. I would think paint would last that long being bombarded by grit off the road. But, you can buy a proper black surround and grill for the A3 from E Bay for £120. Tony

Check to see if the Cambelt and water pump have been changed. Also if it's an auto make sure the gearbox has had services on time. This also goes for the quattro system if it has it. Make sure all electronic items work Especially the mmi and air conditioning etc. Major parts that can fail are dpf, egr or turbo all of which could be £1k bill each. Also check YouTube videos for buyers guides.

It'll definitely need to be coded.

A couple of things to bear in mind …if there’s no exhaust parts hanging down /loose, Maybe a stone trapped between brake disc and backing plate ! It happened to me once! Maybe a damaged backing plate making contact with a brake disc? I noticed a squealing sound at one point … maybe a sticking brake calliper? Are any of your brake disc getting exceptionally hot?

On the AdBlue topic, you can get the no restart message flashed out of the ECU at a fraction of the cost of replacement parts. Give Andy at https://ecuflash.co a call. On the wider get rid or keep topic, I’ll never buy another Audi again. 16 plate B9 (actually B8.5 according to it’s car plate). Owned for 5ish years and I’ve put 50k on it. 80k in total. I’ve spent about 7k keeping it on the road, fixing issues that shouldn’t be there for a car this age and mileage. Not including “on-the-road costs” like tyres. -Had the brake servo/abs issue. -Had the AdBlue issue. -Odometer failed and had to be replaced. -2 broken rear coil springs. -Have the issue with low interior heat. -5 (yes five) new sets of front discs/pads due to excessive warping. -1 new calliper. I can go on, but suffice to say my experience of “Vorsprung durch Technik” is actually “our technology is crap”.

And no vibration at the steering wheel or pedals? In that case I would look to the rear tyres being damaged or out of balance as the most likely candidate. That does not rule out other possibilities such as worn wheel bearings, loose wheel nuts, warped brake discs but they wou;d cause symptoms that you have not mentioned.

Hi all, I have an update... Lol Loud scraping noise = destroyed Balance Shaft Chain & Crank Cog Teeth. Remedy = New Timing Chain & Crank Cog. I did the work myself, which took an age of learning and an age of fixing, but it's all good now. 😁 Thanks, Paul.