spartacus 68

Without service history - walk away.

Had Michelin Cross Climates before - very good all round tyre. That said, all-weather or hybrid tyres are a compromise. Best solution is to source another set of alloys and get dedicated winter tyres. If you have code on your existing alloys just search local Facebook Marketplace, EBAY, or even get a quote from main dealer. They won't be cheap though if new.

According to LLL parts that would be model ABK, sports suspension, orange and pink dots. https://www.lllparts.co.uk/product/8a0411105ac/coil-spring-8a0411105ac See if Bilstein B3s work. Is this 2.0E 115hp Avant? Sports suspension usually dropped ride height by 20mm. https://web1.carparts-cat.com/default.aspx?34=0,1000100011,1000100113&240=0&32=1439&230=29&1271=48&1272=1cc9e4ff-483f-4566-ab54-addbacb15754&10=0F7D38CE93ED4C429D9AE6F283AA2837018004&14=4&12=130

Might be a way simply to get Audi to honour the warranty. The franchise garage submit the claim and Audi UK authorise. Either way - the term probably isn't that helpful. It would be interesting to see the state of the EGR valve. What's the mileage on this 2023 A6?

That’s pretty niche. ABT’s website is clunky and basically a dealer portal. Your best bet is probably searching via UK dealer/importer, as the part you need will be bundled in a full kit and will have a unique ABT part number. Try https://www.specialistvehicles.co.uk/abt/ They have contact number and email and seem to feature Audi as main brand. They are based in Plymouth.

Watch this video from SPR autos in Manchester. They are Mercedes specialists, but I think this illustrates the issue with air con generally, regas being seen as a fix by some and Halfords which just don’t cut it, you name it. It’s a complicated bit of kit. A bubble test is just that, spray on and observe. Plus if you go for nitrogen test (they charge £40), then ideally it could be on for a couple of hours to see if pressure drops. Condenser is a good shout. It’s taking brunt of rain and wind and general debris. Any leak on the reverse you won’t see. And if garage just check for 20 mins, then it won’t reveal true cause. Pressure sensor, genuine is also a good shout. On Audi B8 it’s fairly accessible. SPR made tear mistake and had to strip it down again. Would be useful to pull codes on the car. Search out specialist with real world reviews. Unfortunately these things are never cheap. https://mercedescarservicing.co.uk/youtube/

Put it down to experience and move them on. Any work to make them fit is a compromise. On the positive side, if genuine and refurbished, that’s half the battle.

All the sites you mentioned. Also think about Gumtree. Ultimately, I wouldn’t get too snooty about where the interest comes from. You can tell genuine interested parties from tyre kickers. I personally think an RS4 will go to an enthusiast. Insurance will sort the wheat from the chaff so to speak. Even local classifieds in your newspaper. No experience of Motorway, but sold a 15 plate Polo TDI via webuyanycar on 50k miles a couple of years ago and worked for me. The car was meticulously maintained and bodywork was mint, but you’re dealing with a business that employs people with no knowledge of the motor trade. They check an online register for book price and work down. Low mileage and newer cars, then you’re in with a decent shout. Any DIY maintenance, even documented and receipted, then they class as part history. They want main dealer stamped books. My advice, prepare the car well, have an idea if price, be realistic and enter the lion’s den. That’s used car sales for you. Plus ride shotgun with any test drive, with no one behind you. If it’s nonsense on a phone call or email, move on, the reality is this is what it’s like.

Chances are the headlight is made by Hella. The original OE Audi version will be double that. Even if you're going after-market, then I'd opt for Hella. No point having adaptive headlights if they don't work.

That's atrocious if it was done via insurance, and to be honest it's just as poor if it was cash in hand! Regards the lights - definitely second-hand. Can be refurbished is not available from Audi anymore. Wet sand, then polish with Menzerna. In respect of the water pooling in the boot, they two issues could be completely unrelated, especially in the wiper motor is going haywire. The Valeo unit eventually dies due to the brass/copper pipe that runs to the water jet breaking. This leaks water into the motor and eventually into the boot. There should be an Audi sticker on it - plug and play if you replace. Just get the same part number.

Could be a relay, also check continuity of the wiring if you can trace back.

What’s the fault, what are the symptoms, is this an in-dash error. I take it you haven’t had the car scanned for fault codes? Manual or auto? The electronic parking brake is normally pretty robust. Rear calipers are known to seize, especially at this age, but you’ve already swapped it out. Are you getting 12v to the module? A cheap multi-meter is invaluable. Also check wiring there, especially the ABS wiring.

Coolant leaks rarely get better. I understand it's a lot of money, but you you run a risk on say a longer journey where the car is to temperature, or even dumps coolant and leaves you stranded. Couple of options, park it up until you have the necessary funds and use for short run journeys. Not sure what you have transport wise near you for commuting, but suspect it's a damn sight better than north of the wall!

The sensors come in a matt black plastic. I actually thing that sensor is painted. I could be wrong, but there looks like a corrosion on the surface. Check with Audi, I think it’s called platinum gray and finished in satin matt. Removing the wheel arch isn’t too big a deal. You need to twist the old sensor out and unhook the wiring anyway, so even tight access isn’t likely to work.

When replacing injectors (use a little ceramic grease on the body of the injector) and check if ‘o’ ring if one fitted needs replaced, plus the seating or sealing washer is new, use new stretch bolts and torque to specification, then tighten union nuts to fuel rail. If a new injector it needs coded to the car.

2017 car could be anything, and sounds suspension related.

Front wheel arch liner needs to come off (usually Torx head screws), and depending on location, engine tray too. Parts made by Valeo. Good opportunity to clean out annyway. Easy enough to prep yourself as Audi will charge small fortune for colour coded one. Make a mask template with card, lightly key PDC sensor with 1500 grit sandpaper, wipe sensor with isopropyl alcohol. First coat of plastic primer, couple of top colour coats and followed by a couple of clear lacquer flash coats. Read you can cure paint by popping in oven for a few minutes (without the rubber ‘o’ ring, but think I’d miss that part out, and just don’t jet-wash directly for a few weeks.

Your local Audi dealer knows how to charge, I’ll say that. Some of those prices are frankly ridiculous. Most of it is wear and tear. The thing to remember is the S4 is a performance car and owning one will come with increased costs. There will be a reason the previous owner had a year, and to coin a phrase ‘wants to get out of Dodge!’ Go into it with your eyes open, or increase your budget and look for something a little younger with full service history. A trusted independent garage that are VAG knowledgeable should be able to reduce some of those costs on labour.

They look genuine, thought I saw the Audi rings near the wheel bolts, turn them over, usually a part number on the rear.

Absolutely the right call. Didn’t want to be all doom and gloom, but a dedicated wheel refurbisher will remove the tyre. Sounds basic, but given any corrosion on the alloy face could be on the rim too, then it all kind of makes sense. In addition, whether 1k or 2k paint, it’s impractical to paint an entire rim with aerosols. There are a few tools out there regards aerosols and trigger sprays, but between masking, weather (wind or flies and other debris), it takes what should be straight forward on paper and turns it into a nightmare. You’ve already said you’re a perfectionist. On the positive, if they are genuine Audi alloys, then that’s half the battle.

Pulling the injectors could potentially be down the road if the problem persists, but I think if I was going to do that - then I'd have them measured with VCDS first to see measuring blocks if there's anything amiss. Pulling injectors is never straight-forward, plus you'll need to seat them with new washers and new stretch bolts torqued to specification. There might even be 'o' rings on the body of the injector. In addition, a new injector if that was the case needs to be coded to the car. Also check vacuum hoses for splits. If it's inconsistent, my advice would always be try cheap route first. Forte diesel conditioner straight into your fuel tank when the fuel light is on and drive it like you stole it. Top up with premium diesel and replace the fuel filter as a matter of course. There's not much I'd put in my car additive wise, but Forte is quality. Used to use it on an old A4 quattro V6 around about MOT time to bring down emissions. Good video here on cleaning and reseating injectors on a 4-cylinder from Dave Sterl.

The biTDI engine is a nice bit of kit. As a matter of course you need to run diagnostics using VCDS and see what's happening. Is it a temperature sensor, fuel-related, or mechanical? If there are any existing DTC errors - then they'll show up on the scan. One thing I would check is the fuel-filter. Should be done every 20k miles. Lives under the driver's side on right-hand drive cars and is straight forward to replace. You can use VCDS to prime after changing. MANN or genuine OE if you're changing it. Check the history to see it's been done. That's a Tiptronic 8-speed gearbox and practically bullet-proof. If it was serviced, was it done using genuine ZF oil and filter? Audi say sealed for life, but should be done by 8 years or 75k miles. Cheaper than a new gearbox as you say. Any performance MAPs or running genuine ECU that you know?

Read this from 2022. Crasher (aka Steve Cresswell) is an administrator for the Volkwagen forum and the VW Audi Forum. He's a highly experienced and skilled mechanic with over 40 years service on VAG cars, and suggests to leave the EGR and swirl flaps well alone. https://www.volkswagenforum.co.uk/threads/proboost-remap-does-it-solve-fsi-engine-woes.41306/ The whole thing is a bit handbags at dawn in my opinion regards being removed from A2OC forum. I'm sure there's more to this than meets the eye!

Refurburbishing alloys is a thankless task, and to be honest it’s one of these things best left to the professionals and powder coating, rebalance, etc. That’s different if it was just a scuff, but this is a full strip-down. The time, cost of materials, including zinc etch primer, base coat primer, colour coat and a few coats of lacquer soon mounts up. If you’re determined to do it, then the alloys need to be spotless. Paint wise, then Würth silver metallic is as close to Audi OE as you’ll get.

Pretty sure it’s chain, not cam belt, and quick scan of that Audi package, does not include brake fluid changes, that would be extra.